Hey honey. Yes I have a 2014 Chevy equinox and the gauges...
Responses
JimwF
240 days ago
Hi, my name is\*\*\*\*\* to justanswer. I will be assisting you with your question this evening.
I am sorry that you are having difficulties with your vehicle and I will do my best to help you out.
Did this issue with the gauges happen all at once, or slowly over time?
**\*\*As far as phone calls, If you didn't request it, it is most likely the Website prompting you, not me. A Live Call is a "Premium Service" and will cost more money. I prefer communicating via this site, but in some cases a phone call may be recommended.\*\***
Customer
240 days ago
Hey Jim I'm Heather and no the gauges all went out at the same time but some of the warning lights have been acting crazy for a few months
JimwF
240 days ago
Hi Heather. Pleasure to meet you. Let me take a couple minutes to review this concern, and I will be right back with you.Thanks.
Customer
240 days ago
Sounds good
JimwF
240 days ago
Does your car have the 4 or 6 cylinder [engine](/topics-engine-chevy/)?
Customer
240 days ago
4
JimwF
240 days ago
Thank you
All wheel drive or front wheel drive?
Customer
240 days ago
I've replaced 3 fuses under the hood that said instrument panel fuse block 1, 2 & 3 and I also attempted to find the ground wire. It's a front wheel
JimwF
240 days ago
Thanks again!
Customer
240 days ago
No problem
JimwF
240 days ago
Okay, so there appears to be no technical service bulletins published from GM about this concern.
There are also two fuses in side the vehicle that control the IPC as well. Did you by chance check them? They are located in the instrument panel fuse block, right center of dash. IPC BATT Fuse 10a and IPC IGN Fuse 5a.
JimwF
240 days ago
Here is the schematics to the cluster/IPC.
Customer
240 days ago
We have not replaced those 2 the 10a and 5a inside the vehicle we are getting ready to do that now
JimwF
240 days ago
Okay, good.
JimwF
240 days ago
Any luck?
Customer
240 days ago
No honey the only thing that changed was the engine light went outI'm at my witts end with this. I can't drive at night because the headlights keep cutting on and off while driving
JimwF
240 days ago
I hate to say it but, If the fuse and connections seem okay it will be the cluster itself that needs replacement which is common.
Customer
240 days ago
Okay well thanks Jim I really appreciate your help
JimwF
240 days ago
You are very welcome. Take a look at that schematic I sent you. It has ground wire information as well.
Best of luck with your vehicle, and thanks for using just answer.
Customer
240 days ago
I will and thanks again Jim
JimwF
240 days ago
My pleasure. Have a great evening.
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Rear windshied shattered, how does this happen?
This is absolutely not a normal thing; however, it is not a first occurrence for a Ford Escape. In fact, this event has happened enough times that the National Highway Traffic Safety Administration (NHTSA) began an investigation involving 2010-2011 Ford...
What does the high beams light mean?
The High Beam Lights on your dashboard will indicate the performance of your high beam headlights. It will tell you if they are on or off. To understand the High Beam Lights. Locate the High Beam Lights on your dashboard....
Window not going up or down
The window regulator is most likely broken and needs replaced if you hear the motor crunch when operated. I recommend you have a mechanic like ones from YourMechanic come by to determine why your window is not going up or...
Random sputtering and power loss - 1992 Dodge B350
Hello. There may be separate issues going on here and even the possibility of one causing the other. An overheating engine can misfire and sputter if the engine is extremely hot. Typically this is due to a failed thermostat (https://www.yourmechanic.com/services/thermostat-replacement),...
My truck won't allow me to change gears even when pressing the clutch. No gears go in at all. Makes it impossible to drive.
Hello, this concern is possibly the slave or clutch master cylinder failure. These two components use brake fluid to apply pressure for movement of the clutch system. This fluid breaks down in time and causes the seals to fail (leak)....
Car will start but won't idle
This may be a sign of a failing idle air control valve (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-idle-control-valve). The idle air control valve is located on or near your intake manifold that monitors the air intake as it is mixed with fuel prior to being...
The fuel gauge is not working.
As you may know, your car has a fuel sending unit (https://www.yourmechanic.com/services/fuel-gauge-sender-replacement) inside the fuel tank that operates on a float system. This monitors the level of the fuel in the tank using a float that relays these levels back...
Check Engine code p0016
Hi There, As you know, code P0016 relates to the camshaft position sensor. It sounds like the sensor may not have been replaced or is still producing the same problems that one typically will produce when it is not working...
Browse other content
Maintenance
Services
Estimates
Hey honey. Yes I have a 2014 Chevy equinox and the gauges are not working on the dash. Fuel, rpms, speedometer and I have changed all the fuses that I assume go to it and I have tried to trace down the ground wire but am not sure ...
Hey honey. Yes I have a 2014 Chevy equinox and the gauges are not working on the dash. Fuel, rpms, speedometer and I have changed all the fuses that I assume go to it and I have tried to trace down the ground wire but am not sure where it's located and I'm just a single lady and I don't have any man to help me so do you have any suggestions as to what else I can do before having to pay a mechanic? Mechanic's Assistant: Most vehicles have two fuse panels. Have you located both? Yes Mechanic's Assistant: Are you fixing your Equinox yourself? What have you tried so far? I replaced all 3 that said instrument panel fuse block and yes I am trying to fix it myself Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? No that's good