Kia Borrego Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Kia Borrego Brake Drum Replacement is $336 with $222 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2009 Kia BorregoV6-3.8L	Service typeBrake Drum Replacement	Estimate$582.11	Shop/Dealer Price$705.14 - $1047.23
2011 Kia BorregoV8-4.6L	Service typeBrake Drum Replacement	Estimate$631.31	Shop/Dealer Price$772.66 - $1169.67
2009 Kia BorregoV8-4.6L	Service typeBrake Drum Replacement	Estimate$558.11	Shop/Dealer Price$681.16 - $1023.26
2011 Kia BorregoV6-3.8L	Service typeBrake Drum Replacement	Estimate$677.11	Shop/Dealer Price$829.88 - $1261.22
2010 Kia BorregoV6-3.8L	Service typeBrake Drum Replacement	Estimate$677.11	Shop/Dealer Price$829.93 - $1261.30
2010 Kia BorregoV8-4.6L	Service typeBrake Drum Replacement	Estimate$631.31	Shop/Dealer Price$772.66 - $1169.66

Show example Kia Borrego Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Kia mechanics

Real customer reviews from Kia owners like you.

Excellent Rating

(13)

Rating Summary

13

0

0

0

0

13

0

0

0

0

SEE REVIEWS NEAR ME

Travis

13 years of experience

611 reviews

Travis

13 years of experience

by Henry

Kia Borrego V6-3.8L - Warning Light is on - Minneapolis, Minnesota

Did a good job!

Jason

23 years of experience

190 reviews

Jason

23 years of experience

by Mariya

Kia Borrego V6-3.8L - Car is not starting - Nashville, Tennessee

Great customer service and very punctually.

David

42 years of experience

220 reviews

David

42 years of experience

by Joonwhee

Kia Borrego V6-3.8L - Door Lock Actuator Replacement (Passenger Side Front) - Atlanta, Georgia

It was rainy day. My car was outside. In difficult situation he performed job very well I am very satisfied. JWK Kim

Lee

38 years of experience

228 reviews

Lee

38 years of experience

by Kari

Kia Borrego V6-3.8L - Car is not shifting into park - Oklahoma City, Oklahoma

He was very friendly & explained everything to us perfectly. I highly recommend.

Excellent Rating

(13)

Rating Summary

13

0

0

0

0

13

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Top 10 Scenic Drives in North Carolina

North Carolina is home to a diverse landscape that ranges from the Appalachian Mountains to the Atlantic Coast. This quality makes the state a prime stomping ground for travelers who enjoy the more picturesque side of their surroundings and aren’t...

P2113 OBD-II Trouble Code: Throttle/Pedal Position Sensor "B" Minimum Stop Performance

P2113 P2113 code definition P2113 is a general OBD-II diagnostic trouble code indicating a malfunction with the throttle/pedal position sensor “B” minimum stop performance. This code may be seen with other throttle body or pedal position codes. What the P2113...

How to Take Stickers Off Your Car

Stickers Stickers exist for a variety of ideas, political affiliations, brands, bands, and everything else under the sun. There are even ones out there that represent your child’s report card! Some stickers come attached to the car straight from the...

I have a 2004 honda accord and my front door speakers don't work but everything else does how do I fix?

The first thing to check is to see if the radio has a fader function and front speakers are turned off. If set okay then you will need to try a known good speaker to see if signal is getting...

P0141 OBD-II Trouble Code for a 2005 Honda Accord. Is this serious? Can I drive with it?

You can drive the car normally and get it repaired at your earliest convenience. The trouble code that you are referring to, P0141, typically means that the heater element in an oxygen sensor is not functioning or the circuit to...

I need a good basic diagram for vacuum lines on my 1.8t jetta 2003

The vacuum hose diagram may appear on an under hood label so be sure to check that location first. Generally, the best source for the diagram, as well as all repair and diagnostic information and instructions for the vehicle, is...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com