GMC Yukon XL 2500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a GMC Yukon XL 2500 Brake Drum Replacement is $405 with $243 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2004 GMC Yukon XL 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$681.72	Shop/Dealer Price$820.29 - $1197.72
2003 GMC Yukon XL 2500V8-8.1L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.32 - $1163.77
2003 GMC Yukon XL 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.31 - $1163.77
2009 GMC Yukon XL 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.27 - $1163.70
2002 GMC Yukon XL 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.34 - $1163.81
2001 GMC Yukon XL 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.31 - $1163.77
2000 GMC Yukon XL 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$656.22	Shop/Dealer Price$794.58 - $1171.86
2011 GMC Yukon XL 2500V8-6.0L	Service typeBrake Drum Replacement	Estimate$656.22	Shop/Dealer Price$795.22 - $1172.97

Show example GMC Yukon XL 2500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(6)

Rating Summary

6

0

0

0

0

6

0

0

0

0

SEE REVIEWS NEAR ME

Ned

24 years of experience

52 reviews

Ned

24 years of experience

by Anthony

GMC Yukon XL 2500 V8-8.1L - Oil Change - Phoenix, Arizona

Jason

11 years of experience

97 reviews

Jason

11 years of experience

by Craig

GMC Yukon XL 2500 V8-8.1L - AC Compressor - Scottsdale, Arizona

Great work. Very professional and courteous. Will definitely use again.

Rigoberto

11 years of experience

739 reviews

Request Rigoberto

Rigoberto

11 years of experience

Request Rigoberto

by Doug

GMC Yukon XL 2500 V8-8.1L - Starter - Winnetka, Illinois

Great service. Was on time, professional and knowledgeable. Completed the service quickly and showed me what he did. Highly recommended. Will request Rigoberto again if service is needed

Jose

37 years of experience

21 reviews

Jose

37 years of experience

by David

GMC Yukon XL 2500 V8-6.0L - Lights (Headlamps/beams/brakes) - Winter Garden, Florida

Jose was early which is very much appreciated. He is very friendly, but also professional. I had repaired the car myself, but was missing something in my work. Jose diagnosed it immediately upon arriving. It was such a little thing that I felt embarrassed. Jose is amazing and honest. What a rarity these days. In the future when I can't fix a problem on our vehicles, I'll be calling Jose to take care of us. Thanks Jose, I wish I'd booked you earlier!

Excellent Rating

(6)

Rating Summary

6

0

0

0

0

6

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How Long Does a Courtesy Light Bulb Last?

The The courtesy light bulb is also called a dome light and is located on the ceiling in your vehicle. It is normally towards the front of the car and provides light when you open the car door. This light...

P2501 OBD-II Trouble Code: Generator Lamp/L-Terminal Circuit High

P2501 means there is an issue with the generator lamp control circuit. This could be due to defects in the alternator, battery, or starter.

How to Troubleshoot and Replace a Leaking Valve Cover Gasket

Valve cover gasket leaks usually start when not much oil leaves the engine. It should be repaired before it causes serious damage and costly repairs.

Idle speed too high

The idle speed may be elevated due a a large vacuum leak. When unmetered air has entered the engine, the vehicle may try to compensate by adding fuel. The extra air and fuel translate to an increased idle speed. Have...

If I accelerate my heat blows hot....idle speed blows cool and overheats if at an idle

The heater not working in some cases may be related to the overheating problem you are also having. This may be due to a faulty heater blower motor or potentially a bad heater core (https://www.yourmechanic.com/services/heater-is-not-working-inspection). As you may know, the...

I just used semi synthetic oil instead of full synthetic in my 1996 lincoln town car executive

Hi there. If you asked this question about 10 years ago - then yes, you might have issues with seals or gaskets wearing prematurely. However, as technology has improved, the gap between semi-synthetic and full synthetic is not as big....

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com