Chrysler New Yorker Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chrysler New Yorker Brake Drum Replacement is $258 with $144 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1963 Chrysler New YorkerV8-7.0L	Service typeBrake Drum Replacement	Estimate$673.16	Shop/Dealer Price$796.45 - $1112.34
1988 Chrysler New YorkerV6-3.0L	Service typeBrake Drum Replacement	Estimate$646.65	Shop/Dealer Price$769.88 - $1076.43
1972 Chrysler New YorkerV8-7.2L	Service typeBrake Drum Replacement	Estimate$877.70	Shop/Dealer Price$1064.17 - $1569.49
1963 Chrysler New YorkerV8-6.7L	Service typeBrake Drum Replacement	Estimate$625.16	Shop/Dealer Price$748.44 - $1064.32
1981 Chrysler New YorkerV8-5.2L	Service typeBrake Drum Replacement	Estimate$684.54	Shop/Dealer Price$822.76 - $1183.24
1988 Chrysler New YorkerL4-2.2L Turbo	Service typeBrake Drum Replacement	Estimate$646.65	Shop/Dealer Price$769.87 - $1076.42
1971 Chrysler New YorkerV8-7.2L	Service typeBrake Drum Replacement	Estimate$889.70	Shop/Dealer Price$1075.84 - $1580.92
1991 Chrysler New YorkerV6-3.8L	Service typeBrake Drum Replacement	Estimate$680.73	Shop/Dealer Price$809.63 - $1131.74

Show example Chrysler New Yorker Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(7)

Rating Summary

7

0

0

0

0

7

0

0

0

0

SEE REVIEWS NEAR ME

Matthew

33 years of experience

1222 reviews

Request Matthew

Matthew

33 years of experience

Request Matthew

by Austin

Chrysler New Yorker V8-7.2L - Starter - Norfolk, Virginia

Fantastic service and helpful all the way through. Great guy I'd recommend to anyone who has car troubles.

Nicholas

21 years of experience

354 reviews

Request Nicholas

Nicholas

21 years of experience

Request Nicholas

by Kathryn

Chrysler New Yorker V6-3.0L - Oil Change - Arvada, Colorado

Nicholas is a very knowledgeable Mechanic. I know very little to almost nothing about my car. But I feel like today I know more. Nicholas took his time explaining to me the in and outs of everything he looked at. He gave me recommendations for what steps to take next. He even prioritized the ones that he felt are most important.

Mike

26 years of experience

145 reviews

Mike

26 years of experience

by Terry

Chrysler New Yorker V8-7.2L - Intake Manifold Gaskets - Farmington, Michigan

Great to work with.

Charles

26 years of experience

134 reviews

Request Charles

Charles

26 years of experience

Request Charles

by Anthony

Chrysler New Yorker V6-3.3L - Car is not starting - Federal Way, Washington

Great guy came out helped explained everything went through the steps and was able to solve the problem within great time

Excellent Rating

(7)

Rating Summary

7

0

0

0

0

7

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Top Up Brake Fluid

Brake fluid creates pressure in the brake lines to help stop a car when the brake pedal is pressed. Maintain your brake fluid levels to stay safe.

How to Replace Axle Seals

Axle seals fail when there is a visible leak or a major puddle of gear oil underneath the vehicle. In some cases, the axle may pop out entirely.

P0419 OBD-II Trouble Code: Secondary Air Injection System Relay B Circuit Malfunction

Trouble code P0419 means the secondary air injection system relay B circuit is malfunctioning, often when the weather is too cold.

hardstarting in the morning

Hello. If you are having hard starting in the morning the first thing I would check is the glow plugs (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-glow-plugs-timer). The glow plugs are meant to warm up the engine so that it can start properly, if they are...

2006 hyundai sonata , every time it rains my trunk and drivers back Seats gets soaked

The water leak you are describing probably originates at the trunk weatherstripping, the rear glass and sometimes even the taillights assemblies will leak at their seal to the body. Of course, there could be more than one leak point, too....

often to change transmission fluid

For this model, based on Toyota's normal versus severe conditions maintenance schedule, you should change the ATF fluid, and the ATF filter, every 60,000 miles. If you desire that a certified mechanic from YourMechanic perform that service for you, on...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com