Buick Verano Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(104)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(104)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Buick Verano Tie Rod End Replacement is $156 with $61 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2017 Buick VeranoL4-2.4LService typeTie Rod End - Rear Left Inner ReplacementEstimate$360.75Shop/Dealer Price$432.19 - $624.01
2014 Buick VeranoL4-2.4LService typeTie Rod End - Rear Right Inner ReplacementEstimate$340.75Shop/Dealer Price$412.21 - $604.04
2013 Buick VeranoL4-2.0L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$216.05Shop/Dealer Price$256.33 - $354.64
2015 Buick VeranoL4-2.0L TurboService typeTie Rod End - Rear Right Inner ReplacementEstimate$340.75Shop/Dealer Price$412.19 - $604.00
2016 Buick VeranoL4-2.4LService typeTie Rod End - Front Left Inner ReplacementEstimate$340.75Shop/Dealer Price$412.22 - $604.07
2015 Buick VeranoL4-2.4LService typeTie Rod End - Rear Left Outer ReplacementEstimate$297.79Shop/Dealer Price$358.51 - $518.12
2013 Buick VeranoL4-2.4LService typeTie Rod End - Rear Right Outer ReplacementEstimate$221.05Shop/Dealer Price$261.20 - $359.40
2014 Buick VeranoL4-2.0L TurboService typeTie Rod End - Front Right Outer ReplacementEstimate$221.05Shop/Dealer Price$261.57 - $360.06
Show example Buick Verano Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Buick mechanics

Real customer reviews from Buick owners like you.

Excellent Rating

(104)

Rating Summary
98
2
2
0
2
98
2
2
0
2

Eric

14 years of experience
73 reviews
Eric
14 years of experience
Buick Verano L4-2.4L - Oil Change - Jonesboro, Georgia
Erica provided great customer service

Alfred

13 years of experience
501 reviews
Alfred
13 years of experience
Buick Verano L4-2.4L - Variable Valve Timing (VVT) Solenoid - South San Francisco, California
Arrived early, quick service.

John

19 years of experience
138 reviews
John
19 years of experience
Buick Verano L4-2.4L - Spark Plugs - Austin, Texas
Quick service.

Michael

36 years of experience
71 reviews
Michael
36 years of experience
Buick Verano L4-2.4L - Variable Valve Timing (VVT) Solenoid Replacement - San Antonio, Texas
Michael arrived early and got the job done quickly. My car is running so smoothly now. He answered all my questions, even the ones not directly related to the service he did. I will definitely request Michael for any future work. I highly recommend him!

Excellent Rating

(104)

Rating Summary
98
2
2
0
2
98
2
2
0
2
Number of Buick Verano services completed
1144+
services done by our mechanics
TOTAL NUMBER OF EXPERT Buick MECHANICS
800+
experts on our platform

Recent articles & questions

How to Know If a Used Car Is a Good Deal
When you need to buy a used car, it can be quite difficult to sift through the thousands of used cars for sale in your area. You’ll find used car (https://www.yourmechanic.com/article/how-to-sell-a-pre-owned-car-online_2) advertisements in dealership mailers, in newspaper classifieds, and in...
How to Get a Driver's Permit in All States
Getting a driver's permit is usually the first step to obtaining a driver's license. Check out how to get one according to which state you reside in.
How to Use a Ratchet on a Car
Ratchets are hand-held mechanic tools used with sockets to remove or tighten bolts or lug nuts. Ratchets use leverage in a free-spinning motion.

Do i need a need a new gas cap/do i need an allignment?

Hello! Your question related to the gas cap suggests that you may have the incorrect gas cap installed on your car (if the original problem was in fact the gas cap). Unlike most vehicles in earlier years, these are generally...

is it normal for an engine light that's been reset after service to come back on?

Any given diagnostic trouble code will typically have multiple faults listed as potential causes of "the" code setting. It is possible for one fault (in your case an oxygen sensor that might not be putting out the expected waveform) to...

What type and brand of oil should I use in my 2008Chevrolet suburban LTZ? Over 100k miles

The vehicle calls for synthetic oil that provides better protection and should be on your oil cap indicating the proper weights and the brand should not matter as long as it meets GM standards on the oil cap or in...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com