Hello moose! I hope things are well and the Klondike. I h...
Responses
BrianC115
288 days ago
Hello this is Brian I hope I can help. Yes you should be able to install it and program it through the dealer. If you send me a VIN I may be able to find an aftermarket one that comes programmed for you.
Customer
288 days ago
Thank you. \*\*\*\*\* is 1FBNE31L98DA24680. Please check on an aftermarket part. Also, is the stability control cluster easy to replace and where is it located, exactly? Thanks!!!is it the rsc control module that I need. My diagnosis from Ford was the "stability control cluster" needed to be replaced but I cannot find that part anywhere on the internet. I found the RSC module and an instrument cluster.The alert on my dashboard says to service RSC now and it has a annoying alarm sound that goes off every 3 minutes or so. The ABS light is on as well as they stability control and Etc.
Customer
288 days ago
The diagnosis actually says it is the stability control module. Not cluster. This debility control module needs to be replaced.Rsc module
BrianC115
288 days ago
Sorry for the late response. Ill op-out for that you can deal with your preferred tech. Have a happy holiday.
Customer
288 days ago
I have been responding to you through email. Did you not get my responses?I have been responding by email but no one got back to me.I had already sent the VIN and was waiting for a response. Who did I respond to? It was somebody named Moose.This is super confusing.hank you. My VIN is 1FBNE31L98DA24680. Please check on an aftermarket part. Also, is the stability control module easy to replace and where is it located, exactly? Thanks!!!RSC Control module. Can you find an after-market one that is already programmed for my vehicle? Moose didn't answer me.
BrianC115
288 days ago
Hello, my name is\*\*\*\*\* to JustAnswer and thanks for your question!
The other expert has opted out of this question, that is why you are not receiving replies from him. The RSC on this vehicle is controlled by the ABS module, There is no RSC module. There is a stability control sensor cluster that is used for yaw/pitch data for roll control. If the ABS module needs replacing then it does require dealer programming. It is located behind the [coolant](/topics-coolant-ford/) overflow bottle mounted to the hydraulic control unit. If the stability control sensor cluster requires replacement it also requires programming and configuration and is located under the passenger seat. If you purchase either of these preprogrammed to the VIN, they still require a dealer scanner to identify them to the vehicles network.
If you have any follow up questions, please let me know using the reply button. **_If you are satisfied with my help, please let me know so we can complete your question._**
Thank you for using Just Answer today!
Kind Regards,
Kenny
Customer
288 days ago
It is the cluster. Can you find an aftermarket one? One that matches my VIN?
BrianC115
288 days ago
I am a dealer technician, so I only deal with OEM parts. I will have to do some internet research and see if I can find one. Even if the cluster is programmed to the VIN it still requires configuration with a dealer scan tool. I will reply back when I find an aftermarket one.
Customer
288 days ago
Thank you!!!
BrianC115
288 days ago
You're very welcome!
I am not coming up with anything that is VIN specific, even the aftermarket look to be very close in price to OEM. Click link below...
[https://www.google.com/search?q=2008+econoline+350+Stability+Control+Sensor+Cluster&source=lnms&tbm=shop&sa=X&ved=2ahUKEwjfrr\_irNrtAhV6CjQIHYFZDloQ\_AUoAXoECAwQAw&biw=1280&bih=622](https://www.google.com/search?q=2008+econoline+350+Stability+Control+Sensor+Cluster&source=lnms&tbm=shop&sa=X&ved=2ahUKEwjfrr_irNrtAhV6CjQIHYFZDloQ_AUoAXoECAwQAw&biw=1280&bih=622)
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
How do I set drive lock mode?
When your vehicle is in drive lock mode, all of the doors and the trunk will automatically lock when your vehicle reaches a speed of roughly 10mph. You can manually set drive lock mode with a few easy steps: 1....
Sunroof not working.
If the clutch pedal goes down without engaging the clutch. The fluid level needs to be checked in the clutch reservoir. If the level is good then there is a bad seal on either the master or slave cylinder. If...
Exhaust blowing gray blue smoke when accelerating
Hello. If this occurred right after the oil was replaced, then you need to check the oil level. The symptoms you are having are consistent with someone putting way too much oil in the engine. If this was the case,...
Brakes out hitting hole
Hi there, thanks for writing in about your 2000 Ford E-250. Some master cylinders will let in just a little bit of air when the fluid is splashed around too much in the reservoir, which is likely what has happened to yours....
Code P0016
The OBD-II error code P-0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) is a generic code that indicates that the camshaft position sensor (https://www.yourmechanic.com/services/camshaft-position-sensor-replacement) for bank one does not correlate to the signal from the crankshaft position sensor. Some of the common trigger points that create...
Speedometer is erratic and the S light is on
There are a few different components that can cause these issues. The main one is the vehicle speed sensor (VSS) (https://www.yourmechanic.com/services/speed-sensor-replacement). This is located on your transmission, and communicates to the engine what speed the transmission is receiving. The VSS...
Am I able to drive with misfiring cylinders?
Unfortunately, with two cylinders misfiring, this represents 50% of your motor not firing properly which results in a significant reduction of power output by your engine. While the car may be driven, this may be risky as this may cause...
I have a 95 dodge intrepid. I'm wondering if the control arm and assembly is what is connected to my strut.
Hi there. The struts on the front of your vehicle are attached to the lower control arm with a ball joint, a sway bar with sway bar extensions, the tie rod ends to your steering system, and the knuckle hub...
Charging
Hello, It sounds like you may have faulty voltage regulator that may not be allowing the alternator to charge the battery properly. The voltage regulator is a unit that regulates the charging of the battery by the alternator (https://www.yourmechanic.com/services/alternator-replacement) and...
Browse other content
Maintenance
Cities
Hello moose! I hope things are well and the Klondike. I have a 2008 Ford E350 and the service RSC light an alarm as well as the ABS light is on. The Ford dealership said that it is the stability control cluster that needs to be re...
Hello moose! I hope things are well and the Klondike. I have a 2008 Ford E350 and the service RSC light an alarm as well as the ABS light is on. The Ford dealership said that it is the stability control cluster that needs to be replaced. Other mechanics have told me that they cannot replace it because they don't know how to program it. I was wondering if I could just purchase one and replace it myself and then have the Ford dealership program it. Mechanic's Assistant: Is it just the ABS light? Or is the [brake](/topics-brake-ford/) system warning light on, too? There is no brake system warning. Service RSC now is coming on as well with a dinging sound. It comes on every 3 minutes or so. Mechanic's Assistant: Are you fixing your E350 yourself? What have you tried so far? I've just replaced any fuses pertaining to the ABS and RSC and then I took it to the Ford dealership and they diagnosed it as needing the stability control cluster replaced.