I installed a new ignition switch and ignition cylinder a...
Responses
A. Penland
413 days ago
Welcome to Just Answer. My name is\*\*\*\*\* am a manufacturer trained Ford Senior Master Technician with 30 years of hands on experience. I am here to help. I'm sorry to hear you are having trouble with your vehicle today. The system will offer you a phone call. Feel free to accept or decline this service. It does not come directly from me. I personally cannot provide phone assistance on this website as I only do on line chat. I am usually on line in the evenings after 6:30 PM CST after I get off of work. Please give me a few moments to go over your concerns.
First and foremost let me give you a little information on how this platform works. It is a strict one question one answer service. You ask one question and I will get as many details as I can from you. The reason for this is so I can provide you as accurate an answer as possible. Once I have submitted your answer please feel free to let me know if any clarification is needed about the answer to your question!
Would you mind sending me your VIN and as many details as you can about the problem? This will allow me to give you the most accurate information possible based on your specific vehicle. Please know this is not an auto response message system. I am a full time Ford automotive technician, I review cases as they come in. If you do not receive a prompt response, this means I have stepped away momentarily or are working on your case as well as many others. Please be patient and I will be with you after your reply!
How did you program the new keys to the vehicle?
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
car acts like battery is dead but it's not
Since you have a multimeter, check the battery voltage drop on each battery cable (https://www.yourmechanic.com/services/battery-cable-replacement) to see if the voltage drop is more than .2 volts to the starter and ground. If you have good cables and are getting a...
Bad smell in AC vent
Hi there. This is a concern I have had a lot of experience with. Has the AC drain grommet been updated or removed? The original grommet was designed with a small slit style opening and was found to not be...
Tail lights and running lights won't work - 1996 Toyota RAV4
Hello - check first for a blown fuse since it sounds like all your "rear" lighting has failed. A bad ground for the rear lighting (or broken ground wire) could also cause a complete rear of the vehicle lighting issue....
I have a Chrys 300, when I turn it on and put it into drive I hear a grinding noise. I think it's the drive shaft or differential.
Billing question sent to CS for the cost to repair the driveshaft or differential from making a grinding noise.
where is the crankshaft sensor on an LDV Maxus 2008
Hi there: Unfortunately, we don't service commercial vehicles like the LDV Service van you're referring to in this inquiry. You might want to contact LDV service department (http://www.ldvusa.com/service-and-support/service-tips/) to receive a schematic for your vehicle.
Thermostat stuck
If you are referring to the engine cooling system thermostat, if that thermostat is stuck closed or partly closed, your engine will overheat but such will be obvious upon reading the engine temperature gauge on the instrument panel. Obviously, if...
Why is my check engine light on and my car shakes?
Hi There, This maybe related to potentially a transmission problem resulting from low transmission fluid. As you know, automatic transmissions use pressurized hydraulic fluid to change gears. Every time a gear change is required, the car's computer activates a transmission...
My car makes loud clicking noise when turning
What you're probably hearing is a CV joint. The CV joint is a ball and groove affair that allows the power to be transmitted through the axle even when the car is steering. They usually start to fail around 200...
Idler pulley broke off metal it was attached to after results from a crooked pulley and multiple serpentine belt slips.
You're right in that the stress will be too great and it will come apart again. This is not something you can fix with glue. You will need to take off all of the broken parts and replace them with...
Browse other content
Cities
Estimates
Maintenance
I installed a new ignition switch and ignition cylinder and now my Ford Explorer will not start Mechanic's Assistant: Have you checked the battery, particularly the terminal connections? Are they corroded? Yes connected c...
I installed a new ignition switch and ignition cylinder and now my Ford Explorer will not start Mechanic's Assistant: Have you checked the battery, particularly the terminal connections? Are they corroded? Yes connected corrected. It turns over just won’t start Mechanic's Assistant: What year is your Explorer? 2003 Mechanic's Assistant: Are you fixing your Explorer yourself? What have you tried so far? I have switched out the ignition cylinder and the ignition switch Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? The keys are programmed the new keys