2005 ford focus zx3 standard 5 speed. I need to replace h...
Responses
Dan
275 days ago
Hello, my name is \*\*\*\*\* \*\*\*\*\* I'm sorry to hear about problem. Ignore phone call prompt and there may be short delay between replies.
Dan
275 days ago
You only need to replace the 1 side that is failing, no reason to replace more. Let me know if you have questions or would like replacement instructions. Thanks.
Customer
275 days ago
You can call
Dan
275 days ago
No need for a call. You only need to replace the 1 side that is failing, no reason to replace more. Let me know if you have questions or would like replacement instructions. Thanks.
Customer
275 days ago
Ok thank you! Is it an assembly or different bearings? Like up and lower ball joints.
Dan
275 days ago
It is a assembly, the ball joints are different then wheel bearing. I'll get you a diagram.
Customer
275 days ago
Ok I was just asking like in general
Dan
275 days ago
Just replace the 1 wheel bearing that is noisy/loose and that should solve all of the problem. Let me know how it goes or if you have more questions, thanks.
Customer
275 days ago
how about [exhaust](/topics-exhaust-ford/) leak
Dan
275 days ago
Exhaust leak is usually something best dealt with by a exhaust shop and should be around a $100 repair. Let me know if you have questions, thanks.
Customer
275 days ago
Ok I was told i may also have motor mount issue. How hard is that that to fix and how do I find out exactly where motor mount is broken
Dan
275 days ago
A worn motor mount can allow excessive vibration and lead to exhaust leaks so dealing with the motor mount issue would probably be best first step. Let me know how it goes or if you have questions, thanks.
Customer
275 days ago
Ok can you send me instructions on replacing hub assembly? I know they have to be pressed in and out to avoid damaging them.
Dan
275 days ago
Here are instructions, let me know how it goes or if you run into questions. Thanks.
-
[https://www.dropbox.com/s/ykiu34xyn9eb5rr/hubr1.pdf?dl=0](https://www.dropbox.com/s/ykiu34xyn9eb5rr/hubr1.pdf?dl=0)
-
[https://www.dropbox.com/s/u5ebgh5lm31zrfm/hub2.pdf?dl=0](https://www.dropbox.com/s/u5ebgh5lm31zrfm/hub2.pdf?dl=0)
Customer
275 days ago
Will do thank you!
Dan
275 days ago
I'm happy to help, I'll be here if you run into questions. THanks.
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Leaky water pump
The water pump seems to be a common problem with your Range Rover. If you have any type of warranty, call them to see what they require to cover the repair. If not, the cooling system will need to be...
Broken drive shaft
The damage from the broken drive shaft must be inspected to ensure other components were not damaged in the process. Have an experienced technician, such as one from YourMechanic, look to see if the u-joints failed or if the actual...
Transmission selector shaft seal leakage. Does it need to be fixed and how expensive is the repair?
If you are referring to the "manual shaft" seal pressed into a bore on the transmission case, which seal is typically around an inch in diameter, it is repairable (replaceable) on the car if there is physical access to the...
I have a 2012 Chevy Cruze, the compass, on star and phone stopped working. Can you tell me what's wrong?
Hello. Most of the time if all of these stopped working at the same time then you either have a failure in the body control module or in the communication module. Most of the time this is a body control...
Not starting
The most common cause of an no start with no spark is going to be the crankshaft sensor causing the no start. The vehicle should be scanned to see if there is an input from the crankshaft sensor to the...
What else can be making noise under the front of my 2013 Ford Explorer
Hi there. I have come across this situation with this vehicle a few times. Most of the time it is one of two things. It is either caused by bad strut mounts or by failing lower control arm bushings. The...
When my car starts I see my headlights and indash lights go dim.
A starter motor uses a lot of current and thus will cause a voltage drop at the battery. During the brief interval that a starter engages and runs, any other circuits that are also "on" could see the voltage drop...
My slip indicator light is on all the time. I just had the car serviced and tires rotated. Why would the slip indicator stay on?
Hi there. The Slip indicator light should blink at certain times. If the vehicle stability control system is operating (actively assisting with handling), you’ll see the Slip indicator light blink. This should also be taken as a warning that the...
Shifter loose transmission stuck 1992 Ford F150
Hi there - unhook the shifter from the transmission lever, and try to move the transmission lever to the Park position. If this is successful, start working your way back towards the shift lever on the column. Re-connect the cable...
Browse other content
Maintenance
Estimates
Cities
2005 ford focus zx3 standard 5 speed. I need to replace hub assembly? Is one side ok to change or should both driver and passenger side be changed at same time? Mechanic's Assistant: Are you fixing your Focus yourself? Wha...
2005 ford focus zx3 standard 5 speed. I need to replace hub assembly? Is one side ok to change or should both driver and passenger side be changed at same time? Mechanic's Assistant: Are you fixing your Focus yourself? What have you tried so far? Yes and no! I am having a friend do the manual labor part Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? I am in process of getting new tires also. At least 3 new ones.