Was doing a radiator replacement, got everything done as ...
Responses
Roy Belding
389 days ago
Hello, my name is \*\*\*\*\* \*\*\*\*\* sorry to see you are having issues. Give me a couple of minutes to review your issue and I will assist you
Roy
Good morning
Do you have the 4.0 motor?
Roy
Roy Belding
389 days ago
Let me check.
Roy
Roy Belding
389 days ago
OK, I attached a couple of pictures for you.
Do you mean you cannot get the fans to seat correctly on the radiator?
As far as the lower hose, did you try from the bottom to get to the hose? That is the easiest way to access it.
Can you upload some pictures of what you see?
Roy
Customer
389 days ago
No I can't get fans to come off the new radiator again. So I can replace the radiator again and put the hose on that way
Customer
389 days ago
Customer attachment 9/8/2020 10:52:52 AM
Customer
389 days ago
Customer attachment 9/8/2020 10:52:53 AM
Customer
389 days ago
I tried to pull it off and tried to hammer it out. Stuck
Roy Belding
389 days ago
I know once you release the top bolts, the fans lift up and out of the radiator itself.
What is preventing you from attaching the hose in the car from the bottom? I have never had to remove the fans for this operation.
Roy
Customer
389 days ago
The bolts are removed thats the kicker. It just ont slide out and when I try to pull it off it won't do that either. Has me stumped. And the radiator has two hoses one lower and one higher. The lower one doesn't give me a whole lot of room to work with. Which is why if I can get the fan thing off I can put the radiator back in and put the lower hose on just fine. The fan not coming off is the first issue. Second issue is just a bad clamp which is an easy fix
Roy Belding
389 days ago
Can you lift the radiator and fan assembly out as a unit?
Was the picture you sent with the radiator out of the truck? If so, remove the lower hose at the engine and then attach it to the radiator and then connect it to the engine after you drop it back in.
Roy
Customer
389 days ago
out of the carYeah I dont know why I didn't think of that
Roy Belding
389 days ago
OK, attach the hose with it out. Then attach the other end when you drop it in.
Roy
Customer
389 days ago
Yeah will do. I believe I have it from here thank you.
Roy Belding
389 days ago
LOL, no worries. You are frustrated. Sometimes you have to take a step back and attack from a different angle.
Roy
Customer
389 days ago
YepThank you
Roy Belding
389 days ago
You are welcome
Roy
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Steering wheel hard to turn and vibrates
Low power steering fluid is often the cause of this. If your fluid is low, you could have a leak in the pump or a hose. If your fluid is full, a pump that is not developing enough pressure or...
My car is overheating and I know it's not the radiator why's the reason it's overheating!???!!
The water pump on this engine is driven by the timing belt. You should remove the accessory serpentine belt and start the motor to see if the noise and burning smell is coming from the water pump and timing belt....
Fuel pump was replaced but it is still not working.
Hello. If the fuel pump is not coming on, and the fuse and relay are good, then it may be possible that there is a problem with the pump or the fuel pump circuit. The first thing I would do...
Is a 1994 Jeep Cherokee safe to drive?
Hi there. Without performing an inspection, I could not determine if this vehicle is safe to drive. All SUV's can flip over during an abrupt high speed turn. In fact, all of these types of vehicles today come with this...
Brake pedal goes to the floor
Normally, if there is a hydraulic leak that lets the brake pedal go to the floor, the condition remains until its repaired. with your brakes coming back as you describe, it's hard to say what occurred without knowing more of...
My car pulls/jerks to right when I slow down.
If this is happening without pressing the brake pedal, this may be a sign of worn out wheel bearings. A wheel bearing (https://www.yourmechanic.com/services1/wheel-bearings-replacement) will usually fail due to pitting or small damage on the surface of the rollers or the...
Heating problem
The first thing to confirm is whether or not the engine operating temperature is in the normal range and whether there is sufficient coolant in the radiator. If, for example, the engine cooling system thermostat is stuck open, and thus...
is it possible to replace the a/c clutch and bearing on a mazda protege 5 without replacing the compressor
On almost all A/C compressors, it is possible to replace the clutch without replacing the entire unit. To replace the clutch requires a special tool kit for doing just that. The A/C compressor does have to be removed from the...
I have a 2011 Nissan Sentra, just today it started beeping 16 times when I start the car, no indicator lights.
There are no Technical Service Bulletins (NHTSA) covering this particular issue for your year, make and model and I do not see comparable complaints (http://www.safercar.gov) filed from other consumers. Consequently, the underlying fault will have to be diagnosed as an...
Browse other content
Cities
Estimates
Maintenance
Was doing a radiator replacement, got everything done as said to be done, as I thought. Once completed, I did a second look through to make sure I didn't miss anything looks as if I didn't clamp properly but the lower hose that co...
Was doing a radiator replacement, got everything done as said to be done, as I thought. Once completed, I did a second look through to make sure I didn't miss anything looks as if I didn't clamp properly but the lower hose that connects to the radiator came undone and now i cant get to it to put it back on. So I tried to start from scratch well now the radiotr fan shroud cover won't come the radiator block. Mechanic's Assistant: Has the car been overheating? Have you noticed any leaks? Yes there was a leak from the bottom right of radiator and when I removed the old one notice 2 small holes Mechanic's Assistant: What is the make/model/year of your car? 2008 Chrysler Pacifica Mechanic's Assistant: Are you fixing your Pacifica yourself? What have you tried so far? I was fixing it myself and was able to take the old one out. Bought a new one, sorta used. Installed it and then when I notice the lower hose came undone is when I ran into my new problems. Juat having a hard time reinstall Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? Thats pretty much it