Jeep Commander Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Jeep Commander Brake Drum Replacement is $338 with $243 for parts and $95 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2009 Jeep CommanderV8-5.7L	Service typeBrake Drum Replacement	Estimate$612.73	Shop/Dealer Price$745.29 - $1118.22
2006 Jeep CommanderV6-3.7L	Service typeBrake Drum Replacement	Estimate$600.23	Shop/Dealer Price$733.81 - $1107.51
2010 Jeep CommanderV8-5.7L	Service typeBrake Drum Replacement	Estimate$600.23	Shop/Dealer Price$733.81 - $1107.50
2008 Jeep CommanderV8-5.7L	Service typeBrake Drum Replacement	Estimate$590.73	Shop/Dealer Price$723.28 - $1096.21
2007 Jeep CommanderV8-4.7L	Service typeBrake Drum Replacement	Estimate$600.23	Shop/Dealer Price$733.83 - $1107.54
2006 Jeep CommanderV8-4.7L	Service typeBrake Drum Replacement	Estimate$600.23	Shop/Dealer Price$733.81 - $1107.50
2008 Jeep CommanderV8-4.7L	Service typeBrake Drum Replacement	Estimate$596.23	Shop/Dealer Price$728.66 - $1101.49
2009 Jeep CommanderV6-3.7L	Service typeBrake Drum Replacement	Estimate$596.23	Shop/Dealer Price$729.07 - $1102.21

Show example Jeep Commander Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(249)

Rating Summary

233

8

3

0

5

233

8

3

0

5

SEE REVIEWS NEAR ME

Emmette

36 years of experience

282 reviews

Request Emmette

Emmette

36 years of experience

Request Emmette

by Valerie

Jeep Commander V8-5.7L - Air Filter - Woodbridge, Virginia

Once again, Emmette showed up on time and did a thorough and fantastic job! I will definitely be using him for services in the future. Thank you Emmette for doing a great job and in minimal time.

Jose

17 years of experience

433 reviews

Jose

17 years of experience

by Mariana

Jeep Commander V6-3.7L - AC Condenser Replacement - Vancouver, Washington

This was the first time using your mechanic,like everyone else was very scheptical about the service until I met Jose.he was punctual and professional,knew what he was doing. I've asked other question about my car and he took the time to find the problem and explain. I'm impressed with his knowledge and the time spent .

Justin

8 years of experience

372 reviews

Justin

8 years of experience

by Dan

Jeep Commander V6-3.7L - Serpentine/Drive Belt - Boca Raton, Florida

Probably one of the best around. Professional, answers your questions and best of all, no BS! Highly recommended!

Roberto

12 years of experience

304 reviews

Request Roberto

Roberto

12 years of experience

Request Roberto

by Edwina

Jeep Commander V6-3.7L - Check Engine Light is on - Houston, Texas

Very Mannerable! Excellent Communicator and Honest!

Excellent Rating

(249)

Rating Summary

233

8

3

0

5

233

8

3

0

5

SEE REVIEWS NEAR ME

Recent articles & questions

How Long Does an Evaporative Emission Control Canister Last?

There There are all kinds of features built into your vehicle that help ensure that amount of gasoline vapors that escape from your vehicle are kept to zero or a very small amount. These kinds of fumes can be quite...

Veteran and Military Driver Laws and Benefits in Rhode Island

There There are a number of specific rules and laws that apply to active military members in the state of Rhode Island, as well as quite a few benefits that apply to both current servicemembers and veterans. License and registration...

How to Select a Hybrid Car

Hybrid cars are fuel-efficient and use both gas and electricity to generate power. Choose from parallel, series, full, mild, and plug-in hybrids.

The car is overheating

The normal opening temperature of the thermostat is between 85c and 102c. Your car is running in the middle and this is good. You should not be overheating as this is the normal operating range for your engine. If you...

Check Engine Light is on, trouble code P0011&12. I changed the oil and filter. I need to turn off the engine light to see if that problem is solved.

Hello. If the oil level was low or if the wrong oil war previously used then that can cause these codes to come up. Most of the time though, on this engine, it is caused by a failure in the...

Car shakes when I'm idel. What could be wrong and how much to fix it?

Based on your symptoms of rough idle and a check engine light, I would recommend a check engine light inspection. This will help to determine the exact cause of the rough running and check engine light. Consider YourMechanic as check...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com