Chrysler 300 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chrysler 300 Brake Drum Replacement is $303 with $199 for parts and $104 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1960 Chrysler 300V8-6.7L	Service typeBrake Drum Replacement	Estimate$738.14	Shop/Dealer Price$877.68 - $1242.30
2013 Chrysler 300V8-5.7L	Service typeBrake Drum Replacement	Estimate$548.25	Shop/Dealer Price$668.84 - $1003.55
1963 Chrysler 300V8-6.3L	Service typeBrake Drum Replacement	Estimate$625.16	Shop/Dealer Price$748.49 - $1064.41
2013 Chrysler 300V8-6.4L	Service typeBrake Drum Replacement	Estimate$538.23	Shop/Dealer Price$656.28 - $983.46
2015 Chrysler 300V6-3.6L	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.33 - $1006.05
2016 Chrysler 300V8-5.7L	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.31 - $1006.01
1965 Chrysler 300V8-6.8L	Service typeBrake Drum Replacement	Estimate$637.16	Shop/Dealer Price$760.17 - $1075.84
2010 Chrysler 300V6-3.5L	Service typeBrake Drum Replacement	Estimate$544.23	Shop/Dealer Price$662.59 - $990.00

Show example Chrysler 300 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(952)

Rating Summary

887

30

7

5

23

887

30

7

5

23

SEE REVIEWS NEAR ME

Brandon

18 years of experience

275 reviews

Request Brandon

Brandon

18 years of experience

Request Brandon

by Dennis

Chrysler 300 V6-3.6L - Oxygen Sensor Replacement (Front/Upper/Upstream) - Lilburn, Georgia

Arrived on time and completed the repair quickly. Price was reduced because both sensors did not need replacing. Glad to know there are still honest mechanics like Brandon!

Shaun

10 years of experience

542 reviews

Shaun

10 years of experience

by Del

Chrysler 300 V6-2.7L - Oil Change - Phoenix, Arizona

He was on time , took care of business and explained everything i needed to know to get my 300 performing better

Ramiro

21 years of experience

73 reviews

Ramiro

21 years of experience

by Nabil

Chrysler 300 V6-3.6L - Pre-purchase Car Inspection - Seattle, Washington

Friendly and Professional :)

Peter

36 years of experience

346 reviews

Peter

36 years of experience

by Nathan

Chrysler 300 V6-2.7L - Exhaust Gas Recirculation/EGR Valve - Chula Vista, California

Peter showed up well before our appointment time, Peter was courteous and knowledgable. One of the best mechanics I have encountered in my life.

Excellent Rating

(952)

Rating Summary

887

30

7

5

23

887

30

7

5

23

SEE REVIEWS NEAR ME

Recent articles & questions

4 Essential Things to Know About Your Car’s Moon Roof

The The moon roof on a vehicle is a tinted glass panel that sits on top of the vehicle. It is like a window on top of your car that allows you to open and shut it as you please....

How Long Does a Fuel Injector Last?

The fuel that resides in your gas tank has to be carried to various spots of the engine to be burned and used...

How to Choose and Install Specialty Car Seats

While custom cars commonly see aftermarket (https://www.yourmechanic.com/article/all-about-aftermarket-parts) additions for performance and overall appearance, only a handful of applications call for the addition of aftermarket seats. In some cases, the seats (https://www.yourmechanic.com/article/how-to-clean-leather-seats) are replaced with something more comfortable. This is seen...

Car not accelerating when first started

Hi there. When you let your car sit for a long period of time the gasoline tends to lose its combustibility. Along with sediment settling in your tank this will cause your vehicle to not perform properly. Also a malfunction...

Tcs on all time consumes more petrol??

Hi there: The traction control system uses wheel speed sensors to detect when one or more of the car’s wheels lose grip and traction. When the system registers a loss of traction in one or more of the wheels, a...

what are the two sensors called that I need to replace on my 2013 chevy malibu that reads AC unit off due to high engine temp

Hi Ruben. Thanks for contacting us today. The sensors that will monitor data are the engine temperature sensor and the coolant temperature sensor. They work together to relay data to the ECU. If the engine temperature is too hot, an...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com