Q: Need a price for a wiring harness replacement on an '89 dodge ram d250 Cummins turbo
I need to know how much it would cost to replace a wiring harness on my truck. I've replaced the voltage regulator multiple times because it kept going bad, then I replaced the alternator and battery and now it will not run on the new battery unless connected to another one (jumper).
My car has 67988 miles.
My car has an automatic transmission.
The wiring harness is not available on this vehicle and will need to be repaired. You will need to get the problem diagnosed first by a mechanic like one from YourMechanic. Usually this will be on a time and material charge after diagnosis.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
How do I turn the electronic stability control (ESC) off?
The electronic stability control (ESC) system helps keep your car stable when it is cornering, and when you are driving in dangerous weather conditions. If you would like to turn the ESC off, you can do so by pressing the...
Car won't start due to cracked oil pan
Your car has an aluminum oil pan. They can not be repaired. Driving with an oil leak isn’t safe. Oil can catch fire if it leaks on the exhaust. If you car is cranking, but not starting, there is a...
Tapping noise
The engine may be having a lower engine piston slap noise or the more common timing phasers on the camshafts. First thing to do is to make sure you are running the recommended oil for your engine. If you run...
Car quits a few seconds after start up
Toyota has a TSB that states a no start condition due to water intrusion (https://www.yourmechanic.com/article/how-to-check-for-water-damage-in-a-used-car) in the engine harness. This could be an intermittent condition and is caused due to poor contact from corrosion caused by water ingress. Fault codes...
The car shut off when the oil leaked out after an oil change
If you had the oil changed by a company, then have the vehicle towed or call them and let them get it fixed. If the engine ran without oil, you may have caused internal engine damage. I am not aware...
Where is the kill switch located on 2007 chevy cobalt
There is not a kill switch on this vehicle unless it was put in aftermarket. If you cannot turn over you may have a problem with the passkey system that can cause a no start situation. The system would need...
Door lock cylinder - 2004 Honda Accord
Hello. You should be able to replace the original key without an issue. The problem would be getting it programmed to work with your car. It would be better to get the lock fixed just in case the remote stops...
Upon starting, the vehicle has a dry start for about 5 seconds unless it sits overnight.
Hi there. Check the oil pressure sensor and see if its working or sticking. When the oil pressure sensor is sticking or not working correctly, the computer will cut the ignition and fuel off until oil pressure is met and...
I was told some 4x4 jeep models are primarily front wheel drive then the rears kick in when engaged.
Hi there. To determine if your vehicle or another jeep in that manner is rear wheel drive or front wheel drive, simply look at the transmission. If the transmission is mounted horizontal, then the vehicle is front wheel drive. If...
Related articles
A Buyer’s Guide to the 2012 Dodge Journey
The The 2012 Dodge Journey is easy to drive, and it’s not so large that you will have a difficult time parking it. It’s an attractive vehicle that has the power you need whether you are hauling a full carpool,...
Industry News for Automotive Techs: November 5 - November 11
Tesla buys Grohmann Engineering, Ferrari's future hybrids, next-gen Dodge Charger and Challenger, Nissan e-Power system, and YourMechanic recognition.
B1992 OBD-II Trouble Code: Driver Side, Side mount Air Bag Circuit Short to Vbatt
B1992 trouble code means means that the voltage from the side mount air bag circuit is higher or lower than the parameters set by the manufacturer.
Browse other content
Services
Cities