I’m trying to replace the cam shaft sensor on 2013 Dodge ...


I’m trying to replace the cam shaft sensor on 2013 Dodge Charger 3.6 l where is it located ...

I’m trying to replace the cam shaft sensor on 2013 Dodge Charger 3.6 l where is it located

Automotive Expert
Welcome to JustAnswer. My name is \*\*\*\*\* \*\*\*\*\* I will be doing my best to help you. You will be given an automated offer for a phone call. You may accept or decline that offer. I do not personally offer this service so if you take this offer another tech may call I’m sorry that you’re having trouble with your vehicle. Please understand that I do not know your knowledge or capabilities so I may need to ask questions to gather addtional Information. My goal is to provide you the best service possible . If you have any questions or concerns, please don’t hesitate to let me know. It may take a minute or two for me to respond because I may have to pull up information . Thank you for your patience and will reply as soon as possible. Hello, there are 2, do you have a code setting or another reason for changing a cam sensor? thanks

CodePlz just tell me where the thing is located lol
Automotive Expert
I can send information but I mentioned there are 2 cam sensors Thus why I asked about a code so I can possibly direct to which one

Oh um Oreilleys didn't sayDo they look the same
Automotive Expert
Ok, I will send information on both shortly. I will reply shorty, Please allow me a couple minutes, thanks, \*\*\*\*\* \*\*\*\*\* to chat

Thanku
Automotive Expert
Yes, both look same and same part number. You have a left and right. The left? you have to remove the upper intake manifold. the right? you do not have to. I have attached a file link on your page in .pdf format, If using a phone? you may have to open the file linkf rom your email. In summary, they are in the top of each side cylinder head cover at the rear of the engine. Her is the file link I hope my information has helped. If you have any followup to this question? I am on/off each day and will reply as soon as I am back online and see your reply It was a pleasure speaking with you and hope you have a wonderful remainder of the day. Thanks for using Just Answer

Can u tell me which one is which like which code how do I kno
Automotive Expert
I would need the code number in effort to say which one the code points to otherwise a guess. I am sorry

It's bank twoWhich one is that
Automotive Expert
let me pull that up, back shortly

K
Automotive Expert
Bank 2 if the left bank , left side is the side closest to front of car

That still tells me notta lol can u tell me is it the one I can visibly see or is it under the manifold
Automotive Expert
I am doing my best to help. It means the one you can see without removing the upper manifold

Ok lol cool thanks
Automotive Expert
you are welcome

Now lastly all I gotta do is in do [battery](/topics-battery-dodge/) the black wire and then unscrew the old one put new one in replace battery terminal and I'm good?
Automotive Expert
correct

Okay
Automotive Expert
Hope all goes ok

What others are asking

What does the Tighten Gas Cap message mean?
The Tighten Gas Cap message can appear on the driver information center (DIC). When the DIC displays this message, your gas cap is not properly tightened. After the cap is properly fastened, the alert will go away.
How do I clean the sun roof seal?
If your power sun roof is having a hard time opening or closing, or is making strange noises while doing so, it’s a good idea to clean it. This will increase the health and life of your sun roof. To...
swinging steering wheel 65mph
Hello. It is possible that there is a problem with the wheel bearings (https://www.yourmechanic.com/services/wheel-bearings-replacement), front ball joints (https://www.yourmechanic.com/services/ball-joint-front-replacement), and rear ball joints (https://www.yourmechanic.com/services/ball-joint-rear-replacement), and control arms (https://www.yourmechanic.com/services/control-arm-assembly-replacement). These components have been known to cause the problem you are experiencing. If...
How to use Napa 85-200 12V. 1 Amp. This battery charger is slow.
Hi there. When you get a Napa 85-200 12 volt 1 amp battery charger, first you will need to check the battery for the water level. This is done by removing the caps to the battery. (Warning: Do not remove...
Check Engine Light with P0174 code
As you know, this code relates to a lean fuel condition which can be caused by many different things, some of which you have already addressed. The oxygen sensors, which are part of your emissions system, read exhaust gases to...
Not Changing From E Mode To Hybrid
The illumination of the check engine light tells me that vehicles computer has picked up a fault which may shed some light on the problem causing your stalling concerns. Typically it is not good practice to run a vehicle too...
I changed the battery in my ford explorer 2013 and the lights and radio work but it won't start. It says to push the brake but it won't work.
Hi there. Check to see if the battery cables are tight. If the cables are tight, then check the brake switch on the brake pedal. It may not be responding to the computer as it could be damaged or shorted....
Car issues. I need help to determine what's wrong with it.
First you will need to test compression on all 4 cylinders with all of the spark plugs out and the ignition system disabled. If the compression is good on all of the cylinders, then the valves in cylinder 2 are...
how do i get my dash and tail lights to work they went out back to back
If the headlights or license plate lights come on, that might eliminate the stalk mounted combination switch from consideration, as well as the fuse and/or fusible links. In a situation like this where you know the switch is in the...