Replaced new [water pump](/topics-water-pump-chrysler/) n...
Responses
Bart
261 days ago
Hi I'm Bart. I'll be helping you today.
Customer
261 days ago
Ok I need itDo i need to start over ?
Bart
261 days ago
Have you performed a block test to check for Hydrocarbons in the coolant? This can result from a blown head gasket.
No you're good.
Customer
261 days ago
No but checked oil is perfect and runs great perfect not the slightest miss..After installing everything and bleed tstat would idle perfect for over hour the minute you put in gear and go down the road it starts to climb while still running amazing
Bart
261 days ago
Understood. I think that is our next step here. If the system builds pressure quickly, that could be because you're getting combustion gases in the coolant.
Customer
261 days ago
When I use the thermal laser temperature it never climbs over 145But will try running combustion testWould it run smoothly with broke head gasket? Never had one run this good
Bart
261 days ago
Yes. It can.
Customer
261 days ago
Ok I'll try now do I get back to you ? Or start over?
Bart
261 days ago
You can just reply here. You can always just put "for Bart" in the subject line of a new question I'll be notified.
Customer
261 days ago
Thank you
Bart
261 days ago
You bet.
Customer
261 days ago
One last question would it still idle great for over hour with broke head gasket
Bart
261 days ago
Yes.
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Failing fuses, dashboard warnings all present - 2012 Audi A7 Quattro
Your Audi utilizes an electrical power distribution system which is more computer network like, than older point-to-point wiring systems. There are electrical controllers at key locations in the vehicle (front or back) which distribute power to components located close by,...
What causes the passenger side wheel to wobble as if loose when braking?
It is possible that you may have a lug nut loose. However, if this were the case, the wheel would wobble at all speeds and not just when braking. This may be more likely related to a warped brake rotor...
Dark green sludge
Hi, thanks for writing in. Dark green sludge is most likely grease from an outer CV joint boot that has split open on whichever side you are seeing it. If you would like help with the repairs, consider having an...
Why is car losing power Honda Accord
Hello - based on your description of the vehicle behavior, it would seem like your clutch is slipping (https://www.yourmechanic.com/question/clutch-out-in-car) when you upshift. A worn clutch, weak pressure plate, or clutch disk contaminated by oil, will slip, causing the momentary loss...
Why is my brake pedal going all the way down to the floor?
If you are having to refill the brake fluid from it getting low and the brakes go to the floor means you have a leak in the brake system somewhere. You may have a broken brake line, leaking wheel cylinder...
Feels like something it grinding
It sounds like you may have a failing or worn out wheel bearing. A wheel bearing (https://www.yourmechanic.com/services1/wheel-bearings-replacement) will usually fail due to pitting or small damage on the surface of the rollers or the bearing race. Both the surface of...
How can I rig my trunk to close until I can see a mechanic tomorrow...it has a u shape in the latch and won't stay closed
Hi there. We really don't offer advice on "rigging" components on a vehicle. However, this video may help you (https://www.youtube.com/watch?v=5rqgEzyVlBM).
Emergency brake light not working properly
You will need to have the skid control ECU scanned for proper input from parking brake to see if the fault is in the parking brake, ECU or instrument cluster. A mechanic like one from YourMechanic can come and test...
1992 GMC somoma 4.3 keeps burning fuel pumps as soon as they are put in
Fuel pumps rely on fuel for cooling and lubrication so be sure the tank is always kept at least one-quarter full of fuel. If there is a voltage drop on the supply circuit to the pump, that will cause high...
Browse other content
Estimates
Maintenance
Replaced new [water pump](/topics-water-pump-chrysler/) new [radiator](/topics-radiator-chrysler/) flushed [engine](/topics-engine-chrysler/) had new tsat but removed tstat . Everywhere I point thermal reader shows under 145f but ...
Replaced new [water pump](/topics-water-pump-chrysler/) new [radiator](/topics-radiator-chrysler/) flushed [engine](/topics-engine-chrysler/) had new tsat but removed tstat . Everywhere I point thermal reader shows under 145f but still builds up pressure?? Mechanic's Assistant: Has the vehicle ever overheated? And when was it last serviced? Just did all work. Mechanic's Assistant: What is the make/model/year of your car? 2011 Chrysler [300](/topics-300/) with 3.6l Mechanic's Assistant: Are you fixing your Chrysler 300 yourself? What have you tried so far? Replaced water pump ,radiator , fan, and [thermostat](/topics-thermostat-chrysler/) Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? Still overheats then removed thermostat and still builds up pressure