2007 chevy malibu. How to put a resister to bypass theft ...


2007 chevy malibu. How to put a resister to bypass theft system permanently ...

2007 chevy malibu. How to put a resister to bypass theft system permanently

Automotive Expert
Hello and thank you for using JustAnswer. My name is \*\*\*\*\* \*\*\*\*\* I will do my best to assist you. During this conversation you will be given an automated offer for a phone call. You may accept or decline that offer.I don’t personally offer this service so if you take this another tech may call I’m sorry that you’re having trouble with your vehicle. I will do my best to help you resolve them. Please understand that I do not know your knowledge or capabilities so I may need to ask questions to find out basic information to help solve your specific problem. My aim is to give you the best service possible and to help you. If you have any questions or concerns, please don’t hesitate to let me know. Sometimes it may take a moment for me to respond because I may have to look up information about your concern. I appreciate your patience and will provide responses as soon as possible. I apologize, but due to newer site rules, we are not allowed to provide any directions on bypassing antitheft systems. This for owner's protection as we as ours when a customer does this and then has their vehicle stolen or the person requesting the information is not the actual owner. Again, I do apologize and if you wish for a refund, you can get one. Thanks for using Just Answer and letting me help you. I hope I provided what you needed. If you find more help is still needed, let me know by listing out any remaining questions you have on this concern. I hope the remainder of your day is well.

The car just won't start seems like the best fix car lock light stays on solid when turned to on then wont start tried everything except hooking it up to professional scanner. Guessing the igntion tumbler pass key sensor went bad
Automotive Expert
HI That or the key itself. Did you you do the 30 minute relearn procedure

I did
Automotive Expert
HI Unfortunately it would need to be diagnosed with a professional scan tool

Would you do that before the resistor bypass. Unfortunately would have to tow. What professional scanner would do this and not cost too much
Automotive Expert
HI, The least expensive I know of that will do this and also do programming if required would be the Launch, which is around $900 Personally, I would, but it just depends upon your budget and how much you want to sink into the vehicle

What others are asking

Car makes loud noises
There can be a variety of reasons behind what is causing your Toyota Corolla to make loud noises while driving. Unfortunately without more information, it can be difficult to point you in the right direction. This is when I would...
Car cranks, but doesn't start
Cranking and turning over are essentially the same, so I will assume that it cranks but won't start. There are many variables that go into diagnosing a no-start condition. The fuel pump is just one of many things that can...
Ignition switch worn
Hello. This is a common problem with 2003 Honda vehicles. The wafers in the ignition switch/cylinder are getting stuck in the cylinder, which is causing it to not turn when the key is in it. The ignition switch cylinder will...
Stuck while shifting from second gear to third gear at high RPMs
Chevrolet has a TSB out about a failure with the pressure plate causing hard shifts. The first thing to check is the clutch pedal level when the clutch is being operated if the pedal goes close to or is touching...
oil light on. Will not start.
The low oil level and knocking noise may be very likely related in that this may have caused a number of things to fail such as crankshaft bearings or rod bearings. Depending on the severity of this, it may have...
What is usually the ball park figure to have my rear brake pads, rotors, and calibers replaced?
Billing question sent to CS for the cost of parts and labor to replace the brake pads, rotors, and calipers on a 2003 Cadillac DeVille with a V8-4.6L engine.
Are the wheel bearings in the 98 lincoln navigator pressed in?
Hello. We will be happy to answer your question. The wheel bearings on a Lincoln Navigator are pressed down but not pressed in in the fashion that you may think. They can be removed by hand but you will have...
Hello does coils mess up at the same time? How do you know if dealer fix the problem first time
There is a possibility that a coil can fail close to the same time as each other but not likely. The computer will set a code for each failed coil or cylinder. If a different coil fails then you will...
Some "grunting" or "creaking" when I turn the wheel or go over potholes. Took it in and they found nothing.
The problem sounds like the sway bar link arms are binding when turned and in motion. It is these or the struts are binding.