Q: 2007 saab 9-3 aero turbo the car when is in parking the RPMs go hi and then come back

asked by on March 02, 2017

The car actually RPMs going from normal to real high and then come back to normal in the start again what's wrong with it

Idle Control Valve Replacement $162.54 - $1028.01 Get a Quote

What you are describing sounds like a dirty or failing idle air control valve. The idle air control valve monitors the air intake as it is mixed with fuel prior to being injected into the engine at low speeds and at idle. This valve is controlled by the vehicle’s computer and will adjust idle speed based upon other measurements such as engine temperature, intake air temperature and electrical system load or voltage. This is also an important function when starting the motor as it allows the motor to run and idle on it’s own once the motor fires. When you accelerate, the engine RPM increases, and as you let off the gas, the RPM slowly returns to the normal idling speed with the help of the idle air control valve making the transition from a higher RPM back down to idle speed while adjusting the air/fuel ratio constantly to allow this to happen smoothly. When the engine RPM drops below the normal range of about 800 RPM, this often times will cause the engine to stall indicating a dirty or faulty idle air control valve. I would recommend having an expert from YourMechanic come to your location to diagnose and inspect your vehicle.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

A click is heard, lights flash, and engine shuts down
Hello. The symptoms you are describing can be caused by a few different issues. The first thing I would check is to see if the battery is in good condition, properly charged, and able to pass a load test. I...
Gasoline smell in car when I fill gas tank
The tank seal where the fuel pump is inserted may be leaking or the vent hoses as well. Typing your year model and vent hose schematic into a search engine shows a few pretty detailed listings of what you're looking...
Timing issues? Weird noise when accelerating.
Hi there. Although it's true that faulty or incorrect ignition timing will impact how smooth an engine runs, other issues like mass air flow sensors (https://www.yourmechanic.com/services/mass-airflow-sensor-replacement), O2 sensors (https://www.yourmechanic.com/services/oxygen-sensor-replacement) and crankshaft position sensors (https://www.yourmechanic.com/services/crankshaft-position-sensor-replacement) can also cause similar symptoms. The...
My car cranks but it won't turn on.
Hello, thank you for writing in. When dealing with a cranking, no-start situation you always need to think about the basics. The first three things you need to make sure you have are fuel, air, and spark. If you are...
Engine stalls sometimes but not all the time
Hello, Unfortunately, without additional information as to the make, model and year of your motorcycle it may not be possible to suggest what may be causing it to stall. Depending on whether or not it is fuel injected, or not...
TJ did an inspection on a 2008 Land Rover LR2 @Cars of Tampa Inc. How soon would some of the 'good' things need 2b worked on?
Hi Cassandra: I will try to help you. For safety reasons, the steering gear leak should be repaired first. After that the priority would be the replacement of the axles and then repair of the crankshaft seal leak. Technically, you...
P0016 code for my vehicle vvt, cam solenoid, crank/cam sensor?
Hi there. In general, the P0016 is the OBD-II generic code indicates that the camshaft position sensor for bank 1 does not correlate to the signal from the crankshaft position sensor. In most cases, the causes include the camshaft timing...
Replaced battery 4 days ago. Car crabking but not starting because of anti theft. Had a locksmith reset it. Wont work again, why?
Hi Kyle. Thanks for the question. It's likely that your issue is a security code trapped in the ECU. The unfortunate thing about having a locksmith attempt key or security repairs is that 90% of the time, the ECU thinks...

Related articles

What Do Hose Clamps Do?
Hoses Hoses are used throughout the engine, any time there’s a need to transport fluid from one point to another. Your radiator uses hoses, your heater uses hoses (it’s technically part of the coolant system). Your power steering system uses...
B1200 OBD-II Trouble Code: Climate Control Pushbutton Circuit Failure
B1200 means there is an electrical failure in one or more of the climate control system's pushbuttons, likely caused to a damaged pushbutton.
The Future of Car Ownership
What does the future of car ownership look like?