Volkswagen Transporter Power Steering Pump Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Power Steering Pump Replacement Service

How much does a Power Steering Pump Replacement cost?

On average, the cost for a Volkswagen Transporter Power Steering Pump Replacement is $547 with $407 for parts and $140 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1990 Volkswagen TransporterH4-2.1L	Service typePower Steering Pump Replacement	Estimate$1150.06	Shop/Dealer Price$1377.82 - $2047.33
1992 Volkswagen TransporterL5-2.5L	Service typePower Steering Pump Replacement	Estimate$1093.36	Shop/Dealer Price$1307.78 - $1944.00
1993 Volkswagen TransporterL5-2.4L Diesel	Service typePower Steering Pump Replacement	Estimate$1134.74	Shop/Dealer Price$1359.54 - $2026.83
1991 Volkswagen TransporterH4-2.1L	Service typePower Steering Pump Replacement	Estimate$1134.74	Shop/Dealer Price$1359.54 - $2026.83
1993 Volkswagen TransporterL5-2.5L	Service typePower Steering Pump Replacement	Estimate$1093.36	Shop/Dealer Price$1310.32 - $1948.45
1994 Volkswagen TransporterL5-2.4L Diesel	Service typePower Steering Pump Replacement	Estimate$1134.74	Shop/Dealer Price$1359.78 - $2027.25

Show example Volkswagen Transporter Power Steering Pump Replacement prices

What is the power steering pump and how does it work?

The power steering pump is a belt-driven or electric-driven hydraulic pump that generates the hydraulic pressure needed to provide power steering assist. It develops output pressures of 1,000 PSI or more. The pump output is directed to the steering gear, often a rack and pinion type unit, where the hydraulic pressure pushes on the steering rack, greatly reducing the effort it would otherwise take to turn the steering wheel.

Power Steering

When to consider replacing the power steering pump:

Groaning or whining noise when turning. Noise can occur if there is wear on the pump bearings or impeller vanes. A low fluid level or trapped air can also cause noises. If the pump has already been operating while dry, adding fluid may not resolve the noise and replacement of the pump might be necessary.
Power steering fluid leaks. Leaks can develop at pump seals, threaded connections, hoses, or on the steering rack and pinion unit. Pump seal leaks will generally require a replacement.
Difficult steering. Should you notice it is harder to turn the steering wheel, it might mean the power steering pump output pressure is too low, or there could be blockages in the pump or lines.
Damage to the pump pulley. Should the pump pulley become damaged or is loose on the pump shaft, you might detect vibration, drive belt damage, or hard steering. Either the pulley will have to be serviced or the pump assembly replaced.

How do mechanics replace the power steering pump?

If driven by a drive belt, the power steering pump is bolted to the engine via a bracket that allows for adjustment of the pump drive belt. Once the engine is cold, and safe to work on, the drive belt is removed.
If driven by an electric pump, the pump may be mounted in conjunction with the steering shaft or in conjunction with the steering rack. With either a drive belt or electric pump, removal of any dash, panel, or steering components is performed to access the pump.
The threaded connectors to the pump inlet and outlet are loosened and removed.
Any mounting bolts and brackets are removed so the pump can be removed.
If the old pump has failed catastrophically, or there is reason to suspect contaminants in the power steering hoses, the system is flushed.
The new pump is bolted on, the pressure and return hoses attached and the system is bled of all air. If pump is belt-driven, it is tightened to the manufacturer’s specification.
Finally, the engine is run and the car is road tested to confirm normal steering effort. If a new drive belt was installed, belt tension is measured again, and adjusted as needed, after the belt has run for a few minutes.

Is it safe to drive with a power steering pump problem?

No. If the power steering pump is operated without an adequate amount of fluid, and the pump reservoir will not hold fluid due to a large leak. The pump could seize, which would snap the serpentine belt and likely leave you stranded. If the pump turns and there is adequate fluid, but there is no power assist, it will require much greater effort to turn the steering wheel, and that presents inherent safety risks. Generally, the wisest course is to seek immediate repairs if you suspect a problem with any component in your car’s power steering system.

When replacing the power steering pump keep in mind:

Any belts driving the pump should be inspected and replaced as needed. The pump will only produce the required hydraulic pressure if it is driven by the belt at an adequate speed.
Power steering leaks from aged rubber hoses, particularly where the rubber is crimped to the steel tube, are not unusual and should be carefully inspected. The system operates under high pressure. The fluid is flammable, and if leaking fluid happens to contact a hot engine part, a fire might result. You always want to be sure the hoses and connections are sound.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Volkswagen mechanics

Real customer reviews from Volkswagen owners like you.

Excellent Rating

(13)

Rating Summary

12

1

0

0

0

12

1

0

0

0

SEE REVIEWS NEAR ME

Mark

12 years of experience

349 reviews

Mark

12 years of experience

by Glenn

Volkswagen Transporter H4-1.2L - Brakes, Steering and Suspension Inspection - San Jose, California

Mark is very passionate about cars. He has taken on the challenge of working on my VW bus, and I've been happy with the results. If he sees a problem he works with you to figure out a solution.

Peter

44 years of experience

1397 reviews

Peter

44 years of experience

by RODGELL

Volkswagen Transporter H4-1.6L - Loss of power - Tempe, Arizona

YES!!!!!

Brett

26 years of experience

220 reviews

Brett

26 years of experience

by Brent

Volkswagen Transporter H4-1.5L - Car is not starting - Fort Mill, South Carolina

Brett did a fantastic job. Quickly identified the problem and worked with me to come back and replace the needed part.

Martin

7 years of experience

10 reviews

Martin

7 years of experience

by Mark

Volkswagen Transporter H4-1.8L - Oil/Fluid Leak - Redondo Beach, California

Great and very convenient

Excellent Rating

(13)

Rating Summary

12

1

0

0

0

12

1

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Get Smog Technician Certified in New Mexico

Automotive technician jobs include smog certified emissions inspectors. In New Mexico, you need to work at a certified Air Care location.

How to Replace an Injector Control Pressure Sensor

Diesel engines have an injector control pressure sensor that fails when there is hard starting, decreased power, or an illuminated Check Engine Light.

How to Get Smog Technician Certified in Washington

Automotive technician jobs include smog certified emissions inspectors. In Washington, you need to work at an authorized testing station.

Car overheated

If your radiator is leaking then that will cause your car to overheat. The coolant system is pressurized so if it can not hold pressure then the coolant will begin to boil in the engine causing it to overheat. It...

Loud tick knock around 1500 to 2500 rpm and a little on startup

Hello, thanks for writing in about your 2006 Dodge Stratus. It can be tough to tell the differences between engine noises sometimes. In general, small parts make smaller noises. Bigger parts make deeper noises. Think drums or cymbals. Lifters make...

I have a 04 Ford f150 5.4 L 3v V8 Triton, it diagnosis codes P0340 AND P0345, WHICH IS CRANKSHAFT POSITION SENSOR A BANK 1 CIRCUIT MALFUNCTION AND CRANKSHAFT POSITION SENSOR A BANK 2 CIRCUIT MALFUNCTION, will my truck start if I removed the crankshaft position sensor?

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com