Plymouth Voyager Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Plymouth Voyager Brake Drum Replacement is $377 with $197 for parts and $180 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1987 Plymouth VoyagerV6-3.0L	Service typeBrake Drum Replacement	Estimate$851.68	Shop/Dealer Price$997.12 - $1352.41
1999 Plymouth VoyagerV6-3.0L	Service typeBrake Drum Replacement	Estimate$583.32	Shop/Dealer Price$701.69 - $1011.73
1991 Plymouth VoyagerV6-3.0L	Service typeBrake Drum Replacement	Estimate$784.44	Shop/Dealer Price$931.13 - $1290.03
1989 Plymouth VoyagerL4-2.5L	Service typeBrake Drum Replacement	Estimate$779.68	Shop/Dealer Price$925.10 - $1280.37
1984 Plymouth VoyagerL4-2.6L	Service typeBrake Drum Replacement	Estimate$634.74	Shop/Dealer Price$767.37 - $1122.36
1985 Plymouth VoyagerL4-2.6L	Service typeBrake Drum Replacement	Estimate$812.84	Shop/Dealer Price$966.63 - $1346.83
1985 Plymouth VoyagerL4-2.2L	Service typeBrake Drum Replacement	Estimate$830.84	Shop/Dealer Price$984.14 - $1363.98
1998 Plymouth VoyagerV6-3.8L	Service typeBrake Drum Replacement	Estimate$652.48	Shop/Dealer Price$780.21 - $1108.04

Show example Plymouth Voyager Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Plymouth mechanics

Real customer reviews from Plymouth owners like you.

Excellent Rating

(39)

Rating Summary

34

3

0

0

2

34

3

0

0

2

SEE REVIEWS NEAR ME

Jerel

11 years of experience

125 reviews

Jerel

11 years of experience

by Geraldine

Plymouth Voyager V6-3.0L - Inspection / Diagnostics - Raleigh, North Carolina

Jerel was wonderful. Before doing the job I had requested him to do; he checked my vehicle for other problems and found that my transmission was dying and concluded that there was need to perform the other task. I thank him for saving me money and for his detailed report on the condition of my car.

Alex

22 years of experience

112 reviews

Alex

22 years of experience

by Brenda

Plymouth Voyager V6-3.0L - Alternator - Apache Junction, Arizona

Great Service! Showed up on time. Quick and friendly service Will definitely book him again in the future. Thank you!

John

20 years of experience

568 reviews

John

20 years of experience

by Noreen

Plymouth Voyager V6-3.3L - Radiator - Orlando, Florida

thorough

Noe

36 years of experience

604 reviews

Noe

36 years of experience

by Casey

Plymouth Voyager V6-3.0L - Camshaft Position Sensor - Kent, Washington

Noe was kind, showed up on time, and thorough. We will book with him again.

Excellent Rating

(39)

Rating Summary

34

3

0

0

2

34

3

0

0

2

SEE REVIEWS NEAR ME

Recent articles & questions

Top 10 Scenic Drives in North Dakota

North Dakota doesn’t get a lot of attention as a vacation spot, which is a shame with as much as this state has to offer. While much of it consists of prairie expanses, rural ranches, and oil fields, there is...

P0370 OBD-II Trouble Code: Timing Reference High Resolution Signal A Malfunction

P0370 code means that the optical sensor has missed a number of pulses in the camshaft due to a short in the wiring harness, or a damaged PCM.

Top 10 Car Recalls in History

Car recalls are issued by manufacturers as a preventative and safety measure. Toyota's sticking gas pedals has led to the biggest recall in history.

What does it mean if the Check Engine light comes on in the dash?

Your car is pretty sophisticated. The computer systems are capable of monitoring a number of different aspects of operation, including the exhaust/emissions system, the engine and transmission, and more. If a problem is detected, the Check Engine light is turned...

Truck shutting off after startup.

Hello, when you replaced the plug wires, it sounds like you removed all of them and then installed new wires. When you installed the new wires, it sounds like you got them out of order. The first thing to do...

How to get rid of gasoline odor?

Hi there: You can read this article to give you some good tips on removing odors (https://www.yourmechanic.com/article/how-to-remove-odors-from-your-car) from a vehicle. The best process is to remove the carpet, fully clean underneath, shampoo the carpet and repeat a few times as...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com