Nissan Cube Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Nissan Cube Brake Drum Replacement is $437 with $276 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2012 Nissan CubeL4-1.8L	Service typeBrake Drum Replacement	Estimate$746.80	Shop/Dealer Price$901.64 - $1327.88
2011 Nissan CubeL4-1.8L	Service typeBrake Drum Replacement	Estimate$712.80	Shop/Dealer Price$867.67 - $1293.93
2014 Nissan CubeL4-1.8L	Service typeBrake Drum Replacement	Estimate$712.80	Shop/Dealer Price$867.66 - $1293.93
2013 Nissan CubeL4-1.8L	Service typeBrake Drum Replacement	Estimate$712.80	Shop/Dealer Price$867.62 - $1293.86
2010 Nissan CubeL4-1.8L	Service typeBrake Drum Replacement	Estimate$712.80	Shop/Dealer Price$867.69 - $1293.97
2009 Nissan CubeL4-1.8L	Service typeBrake Drum Replacement	Estimate$712.80	Shop/Dealer Price$867.66 - $1293.93

Show example Nissan Cube Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Nissan mechanics

Real customer reviews from Nissan owners like you.

Excellent Rating

(67)

Rating Summary

64

1

1

1

0

64

1

1

1

0

SEE REVIEWS NEAR ME

Breck

20 years of experience

681 reviews

Breck

20 years of experience

by Timpesi

Nissan Cube L4-1.8L - Car is not starting - Houston, Texas

Fast and helpful

Raymond

27 years of experience

228 reviews

Request Raymond

Raymond

27 years of experience

Request Raymond

by Jose

Nissan Cube L4-1.8L - Transmission Fluid Service - Apple Valley, California

He is the right person for the job done

Manuel

32 years of experience

579 reviews

Manuel

32 years of experience

by Hannah

Nissan Cube L4-1.8L - Brake Rotor/Disc Replacement (Front) - Santa Ana, California

Awesome! Finished quickly, and did an excellent job. Will definitely go to him again

Peter

43 years of experience

1321 reviews

Peter

43 years of experience

by Vickie

Nissan Cube L4-1.8L - Catalytic Converter - Mesa, Arizona

Peter was on time and worked on a very hot day!!!! The car needs a few other repairs and we hope to get Peter Back for the Job. Thanks Again, Peter

Excellent Rating

(67)

Rating Summary

64

1

1

1

0

64

1

1

1

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Drive a Prius in the Winter

Driving Driving during extreme weather conditions brings its own challenges. For example, snow and ice can make roads slippery, causing drivers to lose control of their vehicles. It can also be hard to stop when the roads are too slick....

How to Find the Best Car Loan Rate

Usually, you won’t have the full payment on hand when the time comes to buy a car. Car loans exist to help you purchase a vehicle through funds borrowed through a lending facility or bank. You can get a car...

How Much Does a Mechanic Make in Georgia?

Automotive technician jobs in Georgia have an mean salary of $38k, with some mechanics earning as much as $40k.

What cause my car brakes to grab at low speed. 5 mph

Hi there: In many instances, the issue you're describing with the brakes on your 2000 Lexus L6 is related to wheel rotors that might be warped. The brake rotors (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-warped-rotors) are a component that makes up the modern disc brake...

Installed new battery but car won't start - 2005 Honda Civic

Your symptoms could be caused by several components. At first, it sounds like the starter is cranking, but isn't powerful enough to turn over the engine. This could be due to a bad electrical connection or faulty starter. Replacing the...

When put into gear car revs up then lurches forward then stops it keeps doing it

The problem is going to be in the forward running clutch pact is not engaging until pressure is high. You will need to have transmission rebuilt to repair the transmission. You can rebuild the one you have or replace with...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com