Mercedes-Benz R500 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(10)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(10)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz R500 Brake Drum Replacement is $378 with $216 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2006 Mercedes-Benz R500V8-5.0LService typeBrake Drum ReplacementEstimate$628.34Shop/Dealer Price$766.31 - $1113.27
2007 Mercedes-Benz R500V8-5.0LService typeBrake Drum ReplacementEstimate$594.34Shop/Dealer Price$732.37 - $1079.37
Show example Mercedes-Benz R500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(10)

Rating Summary
9
0
0
0
1
9
0
0
0
1

Joseph

27 years of experience
578 reviews
Joseph
27 years of experience
Mercedes-Benz R500 V8-5.0L - Stabilizer Bar Links Replacement (Front) - Houston, Texas
Great guy and mechanic.

Richard

11 years of experience
450 reviews
Richard
11 years of experience
Mercedes-Benz R500 V8-5.0L - Brake Pads Replacement (Front) - Clinton, Maryland
Wonderfuj! Richard was very professional and courteous and explained everything he had done upon completion of the job. I was very satisfied as I was the first time I use Richard.

Jamie

26 years of experience
30 reviews
Jamie
26 years of experience
Mercedes-Benz R500 V8-5.0L - Starter - North Charleston, South Carolina
Fantastic! Prompt and courteous. Completed job competently, reinstalled my battery and carpet without complaint and cleaned up the area. I would recommend him to anyone who needs service.

Dellano

18 years of experience
513 reviews
Dellano
18 years of experience
Mercedes-Benz R500 V8-5.0L - Car is not starting - Hyattsville, Maryland
Dellano made the necessary checks to the car and determined that the reason for the battery drainage is due to a lack of driving

Excellent Rating

(10)

Rating Summary
9
0
0
0
1
9
0
0
0
1
Number of Mercedes-Benz R500 services completed
110+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

The 10 Most Important Things in Your Car Owner’s Manual
Your owner's manual tells you important information about your car, like how to set up your car, how to check car fluids, and correct tire pressure.
Symptoms of a Bad or Failing Exhaust Manifold
If the exhaust is excessively loud, there are engine performance issues, or the engine bay smells burnt, you may need to replace the exhaust manifold.
P0083 OBD-II Trouble Code: Intake Valve Control Solenoid Circuit High (Bank 2)
P0083 P0083 code definition P0083 is a general OBD-II code indicating a issue with bank 2 intake valve control solenoid. This code may be seen with P0081 and P0082. The vehicle also has a bank 1 valve control solenoid. What...

Check gauge light is on. Air stops cooling

The Check Gauge Light (https://www.yourmechanic.com/services/warning-light-is-on-inspection) comes on to prompt you to look at one of the gauges that is high, such as the coolant gauge for the engine overheating. If the A/C has stopped cooling, then you may have a...

2001 Ford Taurus starting issues

This may be a sign of a faulty ignition coil. Ignition coils (https://www.yourmechanic.com/services/ignition-coil-replacement) are coated with a varnish-like insulation that becomes brittle over time after being stretched then contracted repeatedly. The insulation develops small fractures that open when heated and...

Coolant leak coming from behind the radiator

The coolant leak can only be pinpointed after an inspection but a leaking hose in that location would not be unusual. Coolant leaks can sometimes be either a cause, or a consequence, of overheating. Be sure not to drive the...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com