Lincoln Blackwood Intake Manifold Gaskets Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(7)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(7)

Intake Manifold Gaskets Replacement Service

How much does a Intake Manifold Gaskets Replacement cost?

On average, the cost for a Lincoln Blackwood Intake Manifold Gaskets Replacement is $794 with $234 for parts and $560 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2002 Lincoln BlackwoodV8-5.4LService typeIntake Manifold Gaskets ReplacementEstimate$1088.30Shop/Dealer Price$1230.58 - $1600.70
Show example Lincoln Blackwood Intake Manifold Gaskets Replacement prices

What is an intake manifold gasket and how does it work?

The intake on an engine may be made up of a lower intake manifold and an upper intake manifold or plenum. The lower intake manifold is a cast aluminum or molded plastic chamber bolted to the cylinder head of the engine. The intake manifold must be tightly sealed to the cylinder head(s) using a gasket in order to prevent air, oil, or engine coolant leaks.

When to consider replacing the intake manifold gasket:

Internal or external leaks. Due to constant temperature expansion and contraction of engine parts or overheating, the gasket’s ability to seal properly can be ruined, resulting in problems such as:

  • Internal or external engine coolant leaks. In some applications, the manifold has cooling passages within. If the manifold seal to the engine fails, coolant can leak externally or even into the engine oil crankcase, where coolant can be noticed in the engine oil.
  • Engine overheating. If the leak at the manifold is a leak of engine coolant, it can lead to engine overheating. However, there are other causes of engine overheating, so a mechanic would have to determine the actual cause.
  • External oil leaks. On some 6 and 8 cylinder engines, the intake manifold sits atop an oil-lubricated area of the engine block. If the manifold gasket has failed, oil can leak from the block to the exterior of the engine.
  • Poor engine operation, lean operation, rough idle. Vacuum air leaks into the manifold due to a defective gasket that will upset the air-fuel ratio. The engine may run poorly.
  • Check engine light. Minor leaks at the intake manifold gasket will not usually cause the check engine light to illuminate. However, as a leak persists, it may grow larger and it possible for the leak to degrade engine performance enough that it will cause a trouble code to set, which will cause the check engine light to illuminate.

How do mechanics replace the intake manifold gasket?

  • Working on a cold engine, the engine cover is removed. If the intake manifold has internal cooling system passageways, the engine coolant is drained below the level of those passageways.
  • The accelerator cable assembly and cruise control cable are removed and set aside. All electrical connections and emission and vacuum lines in the way of the intake are removed. Ignition components, such as the coil, are removed as needed. If the car has an upper plenum, that is removed and set aside.
  • If the fuel rail is bolted to the intake manifold, the supply and return connections to the fuel rail are disconnected.
  • Once all connections to the manifold are clear, the manifold is unbolted and removed from the engine.
  • Aluminum and plastic manifolds are checked with a machinist’s straightedge to ensure the surface flatness does not exceed the original equipment manufacturer’s specification. If the surface of a manifold is not flat, the new gasket will not seal properly. Plastic manifolds are checked for cracks, heat damage, and warpage.
  • Once the manifold is deemed re-usable or replaced as needed, the new gasket is applied, the manifold is put in position and the mounting bolts are torqued with a calibrated torque wrench in the OEM specified sequence. In some applications, RTV sealant must be applied in corners of the mounting surface or specified hard-to-seal spots, per the service manual.
  • All removed components are then re-installed in the reverse of the above steps.
  • Finally, the vehicle is run and checked for leaks, and test driven.

Is it safe to drive with an intake manifold gasket problem?

Yes. The principal concern with a leaking intake manifold gasket is potential damage to the engine, depending on where the leak is. Although the vehicle will generally be safe to drive, you should schedule service as soon as possible to minimize the chances of additional costly damage. If the leak involves coolant, it could lead to engine overheating damage or the coolant could contaminate the engine oil, which can damage the engine bearings. If there is an air leak to the cylinders, it can cause lean operation which could overheat the catalytic converter.

When replacing the intake manifold gasket keep in mind:

  • In engines where coolant flows through the intake manifold, a leaking intake manifold gasket can be either the cause of or result of engine overheating. If you have a leaking intake manifold gasket, and the engine has overheated, the entire engine should be inspected for damage, such as a blown head gasket. The engine cooling system thermostat should be replaced because engine overheating can damage the cooling system thermostat.
  • Some car engine designs are more likely than others to experience leaking intake manifold gaskets due to material and design issues. Your mechanic can inform you if your car represents one of these cases. Many times a re-designed gasket, or altered installation technique and torque values, will be relevant to avoid a recurrence of any leaks. Mechanics will consult Technical Service Bulletins to determine if any unique circumstance exists for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Lincoln mechanics

Real customer reviews from Lincoln owners like you.

Excellent Rating

(7)

Rating Summary
5
1
0
0
1
5
1
0
0
1

Scott

37 years of experience
995 reviews
Scott
37 years of experience
Lincoln Blackwood V8-5.4L - Fuel Filter - Scottsdale, Arizona
On time and no messing around

Mike

14 years of experience
176 reviews
Mike
14 years of experience
Lincoln Blackwood V8-5.4L - Control Arm Assembly Replacement (Front Lower Left) - Raleigh, North Carolina
Great work and timely service

Edmar

23 years of experience
246 reviews
Edmar
23 years of experience
Lincoln Town Car V8-4.6L - Intake Manifold Gaskets - Bedford, Texas
will do business again

Tim

31 years of experience
45 reviews
Tim
31 years of experience
Lincoln LS V6-3.0L - Intake Manifold Gaskets - McDonough, Georgia
Tim did a great job replacing the tie rod ends and ball joints as well as replacing the intake manifold gaskets. Car handles real well after getting the front end aligned. The engine warning light is off right now but have had issues with it coming on with lean fuel codes. These codes PO171 & 174 can be caused by several issues with the car and have to be eliminated one at a time it seems, In any case I will use Tim again. Thanks Tim

Excellent Rating

(7)

Rating Summary
5
1
0
0
1
5
1
0
0
1
Number of Lincoln Intake Manifold Gaskets Replacement services completed
77+
services done by our mechanics
TOTAL NUMBER OF EXPERT Lincoln MECHANICS
700+
experts on our platform

Recent articles & questions

How Much Does a Mechanic Make in South Carolina?
Automotive technician jobs in South Carolina have an mean salary of $36k, with some mechanics earning as much as $57k.
How to Get Pre-Approved for a Car Loan
Pre-approved car loans make buying a new car easier. Apply for a car loan before you begin car shopping so you can get the best rate and deal.
How to Buy a Good Quality Deer Warning Whistle
While While you might think that other drivers and obstacles in the road are the largest threats to your safety and that of your passengers, the fact remains that wildlife must also be considered. Deer are probably the most worrisome...

Windshield wipers move slow and get stuck

A few different items can cause the windshield wipers to work slow. The most common causes are the windshield motor beginning to fail (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-windshield-wiper-motor), poor electrical connection at the windshield motor, or high resistance at the wiper motor. A qualified...

My Lexus sc 400 only goes in to reverse. Rpms rev up when in neutral or drive gears

What you are describing is often a sign of low transmission fluid (https://www.yourmechanic.com/services/transmission-fluid-service) or a faulty transmission control solenoid. As you know, automatic transmissions use pressurized hydraulic fluid to change gears. Every time a gear change is required, the car's...

Car is shaking

You might be looking at the air conditioner compressor. It has a clutch on it so that the belt can freewheel around it until the electronic controller turns it on. It might turn on and off a couple of times...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com