Jeep Comanche Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Jeep Comanche Brake Drum Replacement is $331 with $188 for parts and $142 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1991 Jeep ComancheL6-4.0L	Service typeBrake Drum Replacement	Estimate$549.07	Shop/Dealer Price$658.21 - $951.90
1986 Jeep ComancheV6-2.8L	Service typeBrake Drum Replacement	Estimate$658.84	Shop/Dealer Price$793.35 - $1147.27
1990 Jeep ComancheL4-2.5L	Service typeBrake Drum Replacement	Estimate$519.07	Shop/Dealer Price$628.24 - $921.94
1992 Jeep ComancheL4-2.5L	Service typeBrake Drum Replacement	Estimate$519.07	Shop/Dealer Price$628.20 - $921.88
1991 Jeep ComancheL4-2.5L	Service typeBrake Drum Replacement	Estimate$519.07	Shop/Dealer Price$628.26 - $921.98
1986 Jeep ComancheL4-2.1L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$658.84	Shop/Dealer Price$793.34 - $1147.27
1987 Jeep ComancheL6-4.0L	Service typeBrake Drum Replacement	Estimate$669.84	Shop/Dealer Price$804.04 - $1157.74
1987 Jeep ComancheL4-2.5L	Service typeBrake Drum Replacement	Estimate$669.84	Shop/Dealer Price$804.86 - $1159.18

Show example Jeep Comanche Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(9)

Rating Summary

8

0

0

0

1

8

0

0

0

1

SEE REVIEWS NEAR ME

Horus

11 years of experience

122 reviews

Horus

11 years of experience

by daniel

Jeep Comanche L6-4.0L - Serpentine/Drive Belt - San Antonio, Texas

knows his stuff.

Luis

12 years of experience

78 reviews

Luis

12 years of experience

by Colter

Jeep Comanche L6-4.0L - Not able to change gears - Albuquerque, New Mexico

Luis showed up right on time and gave a clear, concise diagnosis.

Augie

31 years of experience

263 reviews

Augie

31 years of experience

by Elise

Jeep Comanche L6-4.0L - Car is not starting - Santa Clarita, California

Augie was professional and courteous. I was nervous the issue wouldn't get solved because of older year of my vechicle, but he was able to figure out the problem in a timely manner. He put all my worries at ease. I appreciate him and all his efforts! Thank you, Augie!

Henry

34 years of experience

171 reviews

Henry

34 years of experience

by Harold

Jeep Comanche L4-2.5L - Clear fluid is leaking - Blackwood, New Jersey

Prompt. Diagnosed the problem. Explained the solution clearly.

Excellent Rating

(9)

Rating Summary

8

0

0

0

1

8

0

0

0

1

SEE REVIEWS NEAR ME

Recent articles & questions

How to Reset a Car Alarm

A A car alarm that is not working at all or not working properly can be extremely annoying to you and your neighbors. It may also put your vehicle at an increased risk for theft (https://www.yourmechanic.com/article/how-to-keep-your-vehicle-safe-from-theft) or vandalism. Almost all...

Industry News for Automotive Techs: September 3-9

A remote assist J2534 tool, Honda's new pedestrian detection technology, and advancement of variable superchargers are some big stories this week.

How to Become a Truck Driver

Truck driving jobs are for local delivery truck drivers or big rig heavy duty truck drivers, which require a commercial drivers' license (CDL).

Oil type - 1999 Toyota Camry

Hello. I would suggest not putting in 20w50 oil as it is too thick and can cause engine damage from tight areas of the engine that will not get oil. You should use 5w30 only (https://www.yourmechanic.com/article/what-type-of-oil-should-i-use).

I have gray smoke coming out of my tailpipe but it's not heavy smoke and my car check engine light is orange my car shut off

You did not mention why the radiator was replaced but I think your engine was overheated causing the head gasket to go bad. This would cause the white smoke out of the tail pipe and an engine misfire and overheating...

Door wont open from the inside or out and i cannot lock/unlock the door. I was also driving the other day and my car died.

With regard to the door lock malfunction, yes, in all probability, the interior panel of the door will have to be removed so that the lock assembly and linkages can be inspected and repaired. A certified mechanic from YourMechanic will...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com