Jeep Cherokee Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Jeep Cherokee Brake Drum Replacement is $300 with $167 for parts and $133 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1989 Jeep CherokeeL6-4.0L	Service typeBrake Drum Replacement	Estimate$702.84	Shop/Dealer Price$837.31 - $1191.20
1976 Jeep CherokeeV8-6.6L	Service typeBrake Drum Replacement	Estimate$668.94	Shop/Dealer Price$804.60 - $1159.72
1979 Jeep CherokeeV8-5.9L	Service typeBrake Drum Replacement	Estimate$874.38	Shop/Dealer Price$1061.39 - $1570.60
1993 Jeep CherokeeL4-2.5L	Service typeBrake Drum Replacement	Estimate$547.22	Shop/Dealer Price$662.03 - $970.45
2016 Jeep CherokeeL4-2.4L	Service typeBrake Drum Replacement	Estimate$560.65	Shop/Dealer Price$681.61 - $1012.89
2000 Jeep CherokeeL4-2.5L	Service typeBrake Drum Replacement	Estimate$547.22	Shop/Dealer Price$662.06 - $970.51
1979 Jeep CherokeeL6-4.2L	Service typeBrake Drum Replacement	Estimate$972.14	Shop/Dealer Price$1180.40 - $1754.07
2014 Jeep CherokeeL4-2.4L	Service typeBrake Drum Replacement	Estimate$574.25	Shop/Dealer Price$697.17 - $1033.63

Show example Jeep Cherokee Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(577)

Rating Summary

543

17

2

4

11

543

17

2

4

11

SEE REVIEWS NEAR ME

Bill

30 years of experience

52 reviews

Bill

30 years of experience

by Jordan Turboff

Cherokee 2015 - Oil Change - Golden, CO

Always professional and does a great job!

Luis

28 years of experience

40 reviews

Luis

28 years of experience

by George Gines

Cherokee 2016 - Bleed Brakes - Buffalo Grove, IL

Did the job quick, was very professional highly recommend!

Nathan

13 years of experience

12 reviews

Nathan

13 years of experience

by Cody Stein

Cherokee 1991 - Tire Rotation - Eugene, OR

Fast, accurate, friendly.

Nathan

13 years of experience

12 reviews

Nathan

13 years of experience

by Cody Stein

Cherokee 1991 - Power Steering Fluid Service - Eugene, OR

Fast, accurate, friendly.

Excellent Rating

(577)

Rating Summary

543

17

2

4

11

543

17

2

4

11

SEE REVIEWS NEAR ME

Recent articles & questions

P0707 OBD-II Trouble Code: Transmission Range Sensor Circuit Low Input

P0707 P0707 code definition P0707 is a generic OBD2 trouble code that points to a fault within the transmission range sensor. This code may be seen with various other transmission codes. What the P0707 code means The P0707 diagnostic trouble...

How to Get an Open-End Lease for Your Next Car

When When it comes to getting a new vehicle, there are two options: You can either purchase your next vehicle, or you can lease it (https://www.yourmechanic.com/article/what-is-the-difference-between-buying-and-leasing-a-new-car). If you opt for the latter, you are left with two more choices: a...

P0431 OBD-II Trouble Code: P0431 Warm Up Catalyst Efficiency Below Threshold (Bank 2)

P0431 means there is a failure in the catalytic converter due to too much or little fuel intake or contamination from engine oil.

Code P0303 cylinder 3 misfire

The symptoms you describe along with the blinking Check Engine Light and P0303 trouble code definitely tell us that you have a misfire in cylinder number 3 (https://www.yourmechanic.com/article/p0303-obd-ii-trouble-code-cylinder-3-misfire-detected-by-spencer-clayton_2). Your engine uses a coil on plug system. This means each individual...

My car won't stay on unless I keep my foot on the gas

Hi There, It sounds like you may have a dirty or failing idle air control valve causing your engine idle to fluctuate. The idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) is a small valve on the engine's intake system that reads the...

Replaced batterybin 2014 ford 150, still no lights, and i hear clicking? What could it be

Leaving the ignition key in any position (other than "start" of course) has no effect on the starter. The starter solenoid is only energized if the key is held in the start position. I would first check to see if...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com