Hyundai Tucson Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(366)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(366)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Hyundai Tucson Brake Drum Replacement is $303 with $208 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2005 Hyundai TucsonL4-2.0LService typeBrake Drum ReplacementEstimate$585.23Shop/Dealer Price$705.29 - $1033.97
2008 Hyundai TucsonV6-2.7LService typeBrake Drum ReplacementEstimate$519.23Shop/Dealer Price$635.31 - $961.00
2007 Hyundai TucsonV6-2.7LService typeBrake Drum ReplacementEstimate$557.23Shop/Dealer Price$677.31 - $1006.01
2013 Hyundai TucsonL4-2.0LService typeBrake Drum ReplacementEstimate$519.23Shop/Dealer Price$635.29 - $960.96
2006 Hyundai TucsonL4-2.0LService typeBrake Drum ReplacementEstimate$557.23Shop/Dealer Price$677.33 - $1006.05
2007 Hyundai TucsonL4-2.0LService typeBrake Drum ReplacementEstimate$557.23Shop/Dealer Price$677.31 - $1006.01
2006 Hyundai TucsonV6-2.7LService typeBrake Drum ReplacementEstimate$564.23Shop/Dealer Price$684.12 - $1012.68
2018 Hyundai TucsonL4-1.6L TurboService typeBrake Drum ReplacementEstimate$586.14Shop/Dealer Price$707.62 - $1032.81
Show example Hyundai Tucson Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Hyundai mechanics

Real customer reviews from Hyundai owners like you.

Excellent Rating

(366)

Rating Summary
349
10
4
0
3
349
10
4
0
3

Robert

10 years of experience
8 reviews
Robert
10 years of experience
Hyundai Tucson L4-2.4L - Brake Pads Replacement (Front, Rear) - Berwyn, Illinois
Robert was very professional and easy to talk to.

Gustavo

15 years of experience
59 reviews
Gustavo
15 years of experience
Hyundai Tucson L4-2.0L - Car is not starting - Hoboken, New Jersey
Gustavo was absolutely amazing! He arrived early, was friendly, professional and knowledgeable, made great recommendations and had all of the work done in no time! When I called customer service to say how satisfied I was with both YourMechanic and Gustavo, John at the call center was equally as amazing, helping me book my next appointment based on Gustavo's recommendations/estimate. I HIGHLY recommend both Gustavo and YourMechanic!!

Manuel

41 years of experience
132 reviews
Manuel
41 years of experience
Hyundai Tucson V6-2.7L - Radiator Hose Repair - Schertz, Texas
It was my first time to use this company and of course I was very apprehensive. Your Mechanic followed through every promise they made. It has been a week now and my car is running great. I definitely will use this company again. Fast and professional service from the call center to the mechanic.

Matthew

12 years of experience
183 reviews
Matthew
12 years of experience
Hyundai Tucson L4-2.4L - Brake Caliper Replacement (Passenger Side Front) - Fishers, Indiana
Was outstanding had a few setbacks finding the missing piece..but nonetheless he was efficient and got the job done. I would highly recommend him for any car work. True Professional!

Excellent Rating

(366)

Rating Summary
349
10
4
0
3
349
10
4
0
3
Number of Hyundai Tucson services completed
4026+
services done by our mechanics
TOTAL NUMBER OF EXPERT Hyundai MECHANICS
1300+
experts on our platform

Recent articles & questions

How Can I Tell If I Need New Tires?
Your Your tires keep you firmly planted on the road. They help ensure your safety when driving in rainy, snowy, hot, or sunny conditions. When your tires are worn, you don’t have the same traction as when they were new....
P2271 OBD-II Trouble Code: O2 Sensor Signal Stuck Rich Bank 1 Sensor 2
P2271 trouble code definition O2 Sensor Signal Stuck Rich Bank 1 Sensor 2 What the P2271 code means This code indicates the...
The Top Seasonal Car Repairs
Cars Cars are complex machines. The performance of your car can be affected by many factors, from the age of the car and its various parts, to how it is driven. Because of all the factors affecting your car and...

Where would the vapor leak detector pump be located on my chrysler sebring convertible.

If you are looking for the pump, it is only on California emissions level vehicles. All others have a purge valve only. If you have the pump, then it will be located on or very near the fuel tank. Look...

Acts like out of gas.sputters dies then runs sputters and dies.gas in it fuel pump working smells like carbon,hot

This may be a result of a faulty oxygen sensor. As you may know the oxygen sensors which are part of your emissions system read exhaust gases to determine whether or not the appropriate amount of oxygen is present in...

Looking for the starter interrupt device put on by dealer

Hello...thank you for your question and I will try to help you on this issue, which is an interesting one because these vehicle "kill switches" have indeed become more common lately. Typically the switch box is under the dash but...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com