Honda S2000 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Honda S2000 Brake Drum Replacement is $345 with $222 for parts and $123 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2004 Honda S2000L4-2.2L	Service typeBrake Drum Replacement	Estimate$593.35	Shop/Dealer Price$717.31 - $1059.96
2005 Honda S2000L4-2.2L	Service typeBrake Drum Replacement	Estimate$567.35	Shop/Dealer Price$691.34 - $1034.00
2003 Honda S2000L4-2.0L	Service typeBrake Drum Replacement	Estimate$567.35	Shop/Dealer Price$691.33 - $1034.00
2002 Honda S2000L4-2.0L	Service typeBrake Drum Replacement	Estimate$567.35	Shop/Dealer Price$691.31 - $1033.95
2000 Honda S2000L4-2.0L	Service typeBrake Drum Replacement	Estimate$567.35	Shop/Dealer Price$691.36 - $1034.03
2001 Honda S2000L4-2.0L	Service typeBrake Drum Replacement	Estimate$567.35	Shop/Dealer Price$691.33 - $1034.00
2009 Honda S2000L4-2.2L	Service typeBrake Drum Replacement	Estimate$573.85	Shop/Dealer Price$697.66 - $1040.19
2008 Honda S2000L4-2.2L	Service typeBrake Drum Replacement	Estimate$573.85	Shop/Dealer Price$698.14 - $1041.04

Show example Honda S2000 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Honda mechanics

Real customer reviews from Honda owners like you.

Excellent Rating

(43)

Rating Summary

36

3

1

2

1

36

3

1

2

1

SEE REVIEWS NEAR ME

Kevin

33 years of experience

234 reviews

Kevin

33 years of experience

by Ray

Honda S2000 L4-2.0L - Pre-purchase Car Inspection - Los Angeles, California

H

26 years of experience

828 reviews

H

26 years of experience

by Jason

Honda S2000 L4-2.0L - Car AC Repair - Sunnyvale, California

Honorio came early and got the job done quickly.

Deane

11 years of experience

340 reviews

Deane

11 years of experience

by John

Honda S2000 L4-2.2L - Pre-purchase Car Inspection - Chula Vista, California

Had I met Deane, I might have rated him even higher. I ordered a pre-purchase inspection and I feel like Deane gave me an honest assessment on the car. After we talked and I told him some things about the car that were not disclosed by the seller, he provided some good advice on how he would proceed. Overall, my experience with Deane was very positive.

Melvin

14 years of experience

158 reviews

Melvin

14 years of experience

by Alan

Honda S2000 L4-2.0L - Brake System Flush - Virginia Beach, Virginia

Very knowledgeable and great service!! Highest recommendation!

Excellent Rating

(43)

Rating Summary

36

3

1

2

1

36

3

1

2

1

SEE REVIEWS NEAR ME

Recent articles & questions

How to Replace Your Air Filter

Before Before it can enter the engine, the engine air filter traps any dust and debris by acting as a shield, blocking its path. Over time, however, these filters can accumulate a lot of dirt and get clogged up (https://www.yourmechanic.com/services/air-filter-is-clogged-inspection),...

P0632 OBD-II Trouble Code: Odometer Not Programmed – ECM/PCM

P0632 means that the PCM is unable to read the odometer due to battery in the vehicle becoming discharged or for electrical reasons.

All About Bodily Injury Liability Insurance

Bodily injury liability insurance helps if you get in a car crash that causes injury or death. Most states require you to buy bodily injury insurance.

Getting code P0446

The code P0446 is most likely due to an inoperative evaporative vent solenoid that will need replacement. The rear axle leak will need to be inspected to see where the leak is for a repair needed. If the rear cover...

Cylinder Deactivation System in Bank 1

The diagnosis and repair of this type of problem will require the work of a professional. The cause may be as simple as a low oil level (https://www.yourmechanic.com/services/oil-level-is-low-inspection) or the need for an oil change (https://www.yourmechanic.com/services/change-oil-and-filter) or as complicated as...

Car engine makes hissing sound when driving and bogs down when idling. 2004 Nissan Maxima

Hi there - you are on the right track. If the hiss comes more directly from the engine (with the hood up for example), you probably have an air leak in the intake tract (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-intake-manifold-gaskets) of the engine. If the...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com