GMC Savana 1500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a GMC Savana 1500 Brake Drum Replacement is $378 with $217 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1997 GMC Savana 1500V8-5.0L	Service typeBrake Drum Replacement	Estimate$916.24	Shop/Dealer Price$1066.56 - $1423.03
2002 GMC Savana 1500V8-5.7L	Service typeBrake Drum Replacement	Estimate$889.23	Shop/Dealer Price$1045.64 - $1406.67
1998 GMC Savana 1500V6-4.3L	Service typeBrake Drum Replacement	Estimate$889.23	Shop/Dealer Price$1045.64 - $1406.66
1996 GMC Savana 1500V8-5.7L	Service typeBrake Drum Replacement	Estimate$832.24	Shop/Dealer Price$982.54 - $1338.98
2003 GMC Savana 1500V8-5.3L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.34 - $1163.81
2013 GMC Savana 1500V6-4.3L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.31 - $1163.77
2007 GMC Savana 1500V6-4.3L	Service typeBrake Drum Replacement	Estimate$656.22	Shop/Dealer Price$794.58 - $1171.86
2010 GMC Savana 1500V8-5.3L	Service typeBrake Drum Replacement	Estimate$656.22	Shop/Dealer Price$795.22 - $1172.97

Show example GMC Savana 1500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(33)

Rating Summary

30

0

0

1

2

30

0

0

1

2

SEE REVIEWS NEAR ME

Clement

27 years of experience

28 reviews

Request Clement

Clement

27 years of experience

Request Clement

by Charles

GMC Savana 1500 V8-5.7L - Fuel Filter - Orlando, Florida

He was very professional.

Joel

21 years of experience

987 reviews

Joel

21 years of experience

by Steve

GMC Savana 1500 V8-5.7L - Power Steering Pump - Jacksonville, Florida

Great guy, friendly and personable. Did a great job on my repair. Will definitely use again.

Rodric

14 years of experience

416 reviews

Rodric

14 years of experience

by Albina

GMC Savana 1500 V8-5.7L - Steering wheel is hard to turn - Marietta, Georgia

Very knowledgeable very professional and was able to answer all my questions

Carlos

16 years of experience

362 reviews

Carlos

16 years of experience

by MAJOR

GMC Savana 1500 V8-5.3L - Engine idle speed is high - Fort Worth, Texas

Carlos is the best mechanic that I have ever had work on my car, He doesent just replace parts, He trouble shoots to find the problem. My car has had this problem for over 6 month & 4 other mechanics have worked on it with no secess. but Carlos found & repaired the problem. Think You Carlos , Major Byrd

Excellent Rating

(33)

Rating Summary

30

0

0

1

2

30

0

0

1

2

SEE REVIEWS NEAR ME

Recent articles & questions

How to Register a Car in Texas

There There are a number of benefits that come with moving to Texas. When you first arrive in the Lonestar state, you will need to take the time to ensure that you are on the right side of the law....

Why You Should Get ASE Certified

Automotive technician jobs pay more and have more security if you're ASE certified. Invest in your career as a mechanic with better credentials.

P0774 OBD-II Trouble Code: Shift Solenoid E Intermittent

P0774 means the PCM registered a problem in shift solenoid E, caused by low ATF level, failed shift solenoid, or blocked transmission passages.

How do I use the auxiliary box?

While your car has a glove box that provides substantial storage for important paperwork, manuals and other items, it also includes an auxiliary box above the glove box. It’s smaller and provides more limited room, but still offers important storage...

car shakes when idle and accelerating

It is very possible that you have a valve cover gasket or spark plug tube seal leak on your vehicle. These type of leaks will allow oil to leak onto the spark plugs causing misfires. When the engine misfires due...

Car Battery completely depleted for no reason

It sounds like you may have a weak battery, a failing voltage regulator or failing alternator. As you may know, the alternator charges the battery while the engine runs by generating amperage and recharging the battery while the engine turns...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com