GMC C2500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a GMC C2500 Brake Drum Replacement is $646 with $247 for parts and $399 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1999 GMC C2500V8-5.0L	Service typeBrake Drum Replacement	Estimate$1196.33	Shop/Dealer Price$1405.43 - $1924.73
1984 GMC C2500V8-5.0L	Service typeBrake Drum Replacement	Estimate$963.17	Shop/Dealer Price$1138.07 - $1554.55
1980 GMC C2500V8-5.7L	Service typeBrake Drum Replacement	Estimate$920.78	Shop/Dealer Price$1093.31 - $1516.23
1983 GMC C2500L6-4.8L	Service typeBrake Drum Replacement	Estimate$950.85	Shop/Dealer Price$1122.55 - $1529.71
1994 GMC C2500V8-6.5L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$1100.33	Shop/Dealer Price$1309.59 - $1828.99
1985 GMC C2500V8-5.0L	Service typeBrake Drum Replacement	Estimate$944.17	Shop/Dealer Price$1117.06 - $1532.04
1986 GMC C2500V8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$967.17	Shop/Dealer Price$1139.43 - $1553.94
1991 GMC C2500V8-5.7L	Service typeBrake Drum Replacement	Estimate$1124.33	Shop/Dealer Price$1334.65 - $1854.85

Show example GMC C2500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(22)

Rating Summary

21

1

0

0

0

21

1

0

0

0

SEE REVIEWS NEAR ME

Blissel

4 years of experience

38 reviews

Request Blissel

Blissel

4 years of experience

Request Blissel

by David

GMC C2500 V8-5.7L - Car is not starting - Fort Lauderdale, Florida

My old truck is not stock and was a good challenge to diagnose. Blissy was punctual, communicative and professional. He listened to my description of the problem and methodically solved it. I’m very pleased to have the use of my truck again.

Russell

24 years of experience

356 reviews

Request Russell

Russell

24 years of experience

Request Russell

by John

GMC C2500 V8-5.7L - Fan Clutch - Portland, Oregon

Marco

29 years of experience

236 reviews

Marco

29 years of experience

by Anthony

GMC C2500 V8-7.4L - Alternator - Corona, California

Great guy, with a great attitude. He was very knowledgeable about the type of truck I have and most definitely I’ll be using him again no doubt about that.

Isai

27 years of experience

230 reviews

Isai

27 years of experience

by Tom

GMC C2500 V8-7.4L - Car is not starting - San Antonio, Texas

Isai was extreemly knowledgable and willing to share his insights. He was also extreemly professional and promt.

Excellent Rating

(22)

Rating Summary

21

1

0

0

0

21

1

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Insurance Requirements for Car Registration in Massachusetts

The The Massachusetts Registry of Motor Vehicles requires all drivers to carry four types of liability automotive insurance, or “financial responsibility,” in order to operate a vehicle legally and maintain vehicle registration. The minimum financial responsibility requirements for drivers are...

How to Obtain a G1 ASE Study Guide and Practice Test

Automotive technician jobs pay more if you’re ASE certified. Get the study guide and practice test to be a G1 Maintenance and Light Repair Technician.

How to Replace a Vacuum Brake Booster Check Valve

Brakes are assisted by the vacuum brake booster check valve that fails when the brake pedal is hard to press, feels spongy, or does not work at all.

Car will not start push button steering wheel will not lock either are they related.

There is a technical bulletin to replace the brake switch and harness. The brake lights not coming on will not let the engine starter operate. The bulletin number is NTB10-139. If you would like a professional to address this issue...

Advice on buying an O3 Hummer H3

Yes they do. I have a lot of customers that have had them go bad, and usually it was before 100,000 miles. Don't buy the Hummer. They have all kinds of problems. That's one of the reasons they stopped making...

My 2001 town and country limited is shaking and making a ticking noise spark plug # 1 had buildup on it

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com