Ford Mustang Mach-E Lubricate Driveshaft at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(19,098)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(19,098)

Lubricate Driveshaft Service

How much does a Lubricate Driveshaft cost?

On average, the cost for a Ford Mustang Mach-E Lubricate Driveshaft is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2021 Ford Mustang Mach-EElectricService typeLubricate DriveshaftEstimate$114.99Shop/Dealer Price$124.99 - $132.49
2022 Ford Mustang Mach-EElectricService typeLubricate DriveshaftEstimate$94.99Shop/Dealer Price$105.01 - $112.52
Show example Ford Mustang Mach-E Lubricate Driveshaft prices

What is lubricating the driveshaft all about?

Along the drivetrain, whenever torque needs to travel from one place to another, a driveshaft is used. Some cars have two driveshafts under them, usually for four-wheel-drive applications. U-Joints are couplings that hold sections of driveshaft together and can withstand large amounts of torque. The U-joint and the slip both need lubrication to work smoothly. This means lubricant needs to be applied to every point where the driveshaft meets another section of shaft or any other part of the vehicle.

Keep in mind:

  • While lubricating will help with scraping noise and minor vibration, it will not repair actually broken parts.
  • Inspect the parts of the the driveshaft to make sure they do not need full replacement.
  • Even small spots of excess wear are bad on parts that withstand so much torque, no problem is too small to be addressed on the driveshaft.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The slip joints and U-joints on all drive shafts are located
  • The Zerk grease fittings on the slip joint and U-joints are located
  • New grease is pumped into the grease fittings with a grease gun
  • The vehicle is lowered off of the jack stands

Our recommendation:

Check the manual of your vehicle to see if the manufacturer has specific instructions on servicing and lubricating the driveshaft. If the manufacturer suggests it is time for a service or if the vehicle has symptoms of a malfunctioning driveshaft, then it should be done immediately. These parts are under a lot of force and will usually fail when the car is in motion. While under the vehicle, inspect all of the connections along the drivetrain and keep an eye out for any parts that seems excessively worn. Bring a rag and wipe any mud or dust off to check for damage.

What are the common symptoms indicating you need to lubricate the driveshaft?

  • Clicking or grating sounds while the vehicle is in gear
  • Vibration in the vehicle while it is running

How important is this service?

This service is very important. Poor lubrication is one of the top reasons why driveshafts fail. When they do fail, driveshafts will fail while in motion and can take out more expensive parts around them. These preventative maintenance steps are extremely important in order to avoid more costs down the road.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(19,098)

Rating Summary
17,917
636
124
102
319
17,917
636
124
102
319

Carlton

39 years of experience
14 reviews
Carlton
39 years of experience
Ford F-150 V8-5.0L - Lubricate Driveshaft - Woodbridge, Virginia
He was not able to perform the service because my drive shaft is sealed. He took a look at it and said it was good, however after I started driving again, the clunk and noise is still there. I am not satisfied with the service provided by your website. I paid $80 for a person to come over and do and inspection on my car. Had I taken the truck to his shop he would have not charged me after looking at it for 2 minutes like he did at my home. I think it’s fair to pay the gentleman for his time and drive ($40), however I don’t think it’s for for me to pay you the remainder. If you are going to offer these types of services, the. Your website should be savvy enough to be able to tell me that this job was not one he could have done at my home and saved me the money. I feel like I should get a partial refund since the job was not done. I should note that Carlton “Wayne” was great.

Breck

20 years of experience
681 reviews
Breck
20 years of experience
Ford F-250 Super Duty V8-6.4L Turbo Diesel - Pre-purchase Car Inspection - Houston, Texas
Breck was very knowledgeable and very friendly guy....Thank goodness for honest people.

Christopher

25 years of experience
80 reviews
Christopher
25 years of experience
Ford Escape L4-2.5L - Drive Belt Tensioner - Metairie, Louisiana
Mr. Chris was very kind and helpful. He came in, did the job quickly and really made sure that everything on my truck was in good working condition. I will definitely be using his services again!

Michael

4 years of experience
233 reviews
Michael
4 years of experience
Ford F-150 V8-4.6L - Car is not starting - Indianapolis, Indiana
Great and honest mechanic

Excellent Rating

(19,098)

Rating Summary
17,917
636
124
102
319
17,917
636
124
102
319
Number of Ford services completed
210078+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

How to Buy Good Quality Ball Joints
Even Even though the name sounds small, the function is big. Ball joints help support your car’s weight by serving as a connection and pivot point between the suspension and your tires. In today’s cars these parts are typically lubricated...
P0007 OBD-II Trouble Code: Fuel Shutoff Valve "A" Control Circuit High
P0007 P0007 code definition The P0007 code is associated with an electrical circuit which connects from your engine computer to your fuel system and is most commonly found on diesel engines. It also may be related to other codes, such...
P0137 OBD-II Trouble Code: O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)
P0137 code definition O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2) What the P0137 code means P0137 is the OBD-II generic...

How do you use the Daytime Running Lights?

If your car is equipped with Daytime Running Lights (not available on all Fusions), they provide substantially better visibility during daytime driving. Unlike your headlights, the Daytime Running Lights are designed to make your car more visible to other drivers...

Donde esta ubicado el fusible o relay de los fog lights en 2008 Dodge charger SXT

The fog light fuse and relay are usually in the under hood fuse box. If the lights are not working, these components can be tested using a volt ohmmeter. Note that grounding is very important and failure of the lighting...

I'm replacing the thermostat in my 2000 crv. I'm having trouble getting the temp sensor off because I don't have the right socket. Wondering if there's a different way I can take it off?

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com