Chrysler Dynasty Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(82)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(82)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Chrysler Dynasty Water Pump Replacement is $286 with $104 for parts and $182 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1992 Chrysler DynastyL4-2.5LService typeWater Pump ReplacementEstimate$421.34Shop/Dealer Price$480.98 - $649.37
1993 Chrysler DynastyV6-3.3LService typeWater Pump ReplacementEstimate$791.68Shop/Dealer Price$850.94 - $1012.24
1990 Chrysler DynastyV6-3.3LService typeWater Pump ReplacementEstimate$1235.35Shop/Dealer Price$1499.15 - $2285.14
1993 Chrysler DynastyL4-2.5LService typeWater Pump ReplacementEstimate$803.80Shop/Dealer Price$866.19 - $1036.64
1990 Chrysler DynastyV6-3.0LService typeWater Pump ReplacementEstimate$848.51Shop/Dealer Price$1017.52 - $1514.81
1992 Chrysler DynastyV6-3.3LService typeWater Pump ReplacementEstimate$397.51Shop/Dealer Price$452.03 - $609.77
1991 Chrysler DynastyL4-2.5LService typeWater Pump ReplacementEstimate$409.63Shop/Dealer Price$467.02 - $633.73
1990 Chrysler DynastyL4-2.5LService typeWater Pump ReplacementEstimate$669.91Shop/Dealer Price$792.35 - $1154.25
Show example Chrysler Dynasty Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(82)

Rating Summary
75
3
0
1
3
75
3
0
1
3

Robert

21 years of experience
1307 reviews
Robert
21 years of experience
Chrysler Dynasty V6-3.3L - Oil Pan - Broomfield, Colorado
He is very down to earth and willing to do whatever it takes to get the job done. I'm very greatful for all the hard work he put in on such a cold day.

Robert

22 years of experience
64 reviews
Robert
22 years of experience
Chrysler Crossfire V6-3.2L - Water Pump - Redmond, Washington
Robert was friendly and knowledgeable about my kinda rare car (Chrysler Crossfire). He was done early and the was car was cleaner after he left than when he arrived. I definitely recommend Robert. Nice work!

Aurelio

37 years of experience
82 reviews
Aurelio
37 years of experience
Chrysler 300 V8-6.4L - Water Pump - Schertz, Texas
Excellent service from Aurelio, he was knowledgeable and I felt that my car was in the hands of an expert. I highly recommend Aurelio.

Joe

21 years of experience
126 reviews
Joe
21 years of experience
Chrysler 300 V6-3.5L - Water Pump - Chicago, Illinois
Fast and efficient work

Excellent Rating

(82)

Rating Summary
75
3
0
1
3
75
3
0
1
3
Number of Chrysler Water Pump Replacement services completed
902+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chrysler MECHANICS
1200+
experts on our platform

Recent articles & questions

B1326 OBD-II Trouble Code: Door Ajar Lamp Circuit Short to Ground
B1326 means there is a circuit error with the door ajar lamp, likely due to a defective door ajar switch, defective door switch, or short circuit.
How to Get the Best APR on a Car Loan
The The Annual Percentage Rate (APR) of your car loan is the yearly interest rate on any money you borrow from a lender. The APR includes such things as the principal, any taxes on the vehicle, and any interest and...
How to Search for a New Car Online at CarsDirect
The internet has revolutionized how people shop. Everything from clothing to groceries can be bought online. It only makes sense that the internet would also dramatically change the way people shop for cars (https://www.yourmechanic.com/article/how-to-buy-a-car). CarsDirect is a website (https://www.yourmechanic.com/article/how-to-buy-a-car-online-by-elan-mcafee) that...

Tranny fluid leaked out while driving.

Hi there. A transmission is a hydraulic system, which requires constant flow of fluid to operate the internal components inside. If you have transmission fluid that is leaking, you might want to first find out where the leak is coming...

Car shudders when accelerating and going uphill, seems like a loss of power, particularly around 1500 rpms.

Hi Zach. Thanks for contacting us tonight. There are multiple things that can cause a shaking or vibrating issue like you've described. The most common source of this issue is a loose vacuum line or even loose or faulty motor...

Truck won't start, but lights come on and flicker

What you are describing sounds like a faulty starter solenoid. A faulty starter solenoid (https://www.yourmechanic.com/services/starter-replacement) will generally produce a clicking sound when turning the key. The starter solenoid is located on the starter and has internal electrical contacts that transmit...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com