Chrysler Concorde Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(82)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(82)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chrysler Concorde Brake Drum Replacement is $266 with $171 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1999 Chrysler ConcordeV6-3.2LService typeBrake Drum ReplacementEstimate$539.23Shop/Dealer Price$655.29 - $980.97
1996 Chrysler ConcordeV6-3.5LService typeBrake Drum ReplacementEstimate$538.23Shop/Dealer Price$656.31 - $983.51
2001 Chrysler ConcordeV6-2.7LService typeBrake Drum ReplacementEstimate$519.23Shop/Dealer Price$635.31 - $961.00
1999 Chrysler ConcordeV6-2.7LService typeBrake Drum ReplacementEstimate$519.23Shop/Dealer Price$635.29 - $960.96
1996 Chrysler ConcordeV6-3.3LService typeBrake Drum ReplacementEstimate$538.23Shop/Dealer Price$656.33 - $983.54
1998 Chrysler ConcordeV6-2.7LService typeBrake Drum ReplacementEstimate$538.23Shop/Dealer Price$656.31 - $983.50
1993 Chrysler ConcordeV6-3.3LService typeBrake Drum ReplacementEstimate$544.23Shop/Dealer Price$662.15 - $989.22
1994 Chrysler ConcordeV6-3.3LService typeBrake Drum ReplacementEstimate$544.23Shop/Dealer Price$662.59 - $990.00
Show example Chrysler Concorde Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(82)

Rating Summary
71
9
2
0
0
71
9
2
0
0

Brandon

18 years of experience
275 reviews
Brandon
18 years of experience
Chrysler Concorde V6-3.5L - Cooling System Flush - Stone Mountain, Georgia
Wonderful

Terry

31 years of experience
99 reviews
Terry
31 years of experience
Chrysler Concorde V6-3.2L - Camshaft Position Sensor - Fort Worth, Texas

Mostafa

19 years of experience
62 reviews
Mostafa
19 years of experience
Chrysler Concorde V6-3.5L - Battery Terminal Ends - Lithia Springs, Georgia
Excellent, fast service!

Mario

20 years of experience
110 reviews
Mario
20 years of experience
Chrysler Concorde V6-3.5L - Water Pump - North Fort Myers, Florida
Excellent service from a very knowledgeable technician that I would highly recommend to anybody that needs work done

Excellent Rating

(82)

Rating Summary
71
9
2
0
0
71
9
2
0
0
Number of Chrysler Concorde services completed
902+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chrysler MECHANICS
1200+
experts on our platform

Recent articles & questions

How to Replace a Lost or Stolen Car Title in Washington
Have Have you recently gone on a hunt for your car title only to come up empty-handed? Well you're not alone. Plenty of people each year lose their car title, damage it, or even have it stolen. This car title...
How to Replace Your Air Filter
Before Before it can enter the engine, the engine air filter traps any dust and debris by acting as a shield, blocking its path. Over time, however, these filters can accumulate a lot of dirt and get clogged up (https://www.yourmechanic.com/services/air-filter-is-clogged-inspection),...
What Does the Trunk Open Warning Light Mean?
The trunk open warning light indicates when your trunk is not properly closed. If you are unable to close it, the latch may need to be fixed.

Radio’s touchscreen died, what’s the problem?

Your touch screen system has a recall, R40 dated 7/28/2015, that pertains to the radio system being susceptible to a security vulnerability. The vulnerability could allow someone to access the system which could cause problems. The dealer will reprogram your...

Grinding noise while driving

That sounds about right and here is a good way to test it: Go down a road on a Sunday morning, early when there is hardly anybody around, and go around 45-50 mph, gradually going to the left and right....

Firing order from the front of the engine.

The location of the ignition coil for the 3rd cylinder is the 3rd cylinder back from the front of the engine where the belts are. From viewing the engine from the front of the vehicle, the 3rd cylinder will be...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com