Chevrolet Silverado 1500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet Silverado 1500 Brake Drum Replacement is $351 with $237 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2015 Chevrolet Silverado 1500V6-4.3L	Service typeBrake Drum Replacement	Estimate$838.86	Shop/Dealer Price$1016.71 - $1512.00
2019 Chevrolet Silverado 1500L4-2.7L Turbo	Service typeBrake Drum Replacement	Estimate$657.74	Shop/Dealer Price$798.84 - $1183.81
2005 Chevrolet Silverado 1500V8-5.3L Hybrid	Service typeBrake Drum Replacement	Estimate$634.92	Shop/Dealer Price$770.31 - $1138.17
2005 Chevrolet Silverado 1500V8-6.0L	Service typeBrake Drum Replacement	Estimate$1014.54	Shop/Dealer Price$1215.92 - $1734.59
2019 Chevrolet Silverado 1500V8-5.3L	Service typeBrake Drum Replacement	Estimate$657.74	Shop/Dealer Price$798.87 - $1183.85
2017 Chevrolet Silverado 1500V8-5.3L Hybrid	Service typeBrake Drum Replacement	Estimate$657.74	Shop/Dealer Price$798.84 - $1183.81
2009 Chevrolet Silverado 1500V8-6.0L Hybrid	Service typeBrake Drum Replacement	Estimate$656.22	Shop/Dealer Price$794.58 - $1171.86
2008 Chevrolet Silverado 1500V8-5.3L	Service typeBrake Drum Replacement	Estimate$888.82	Shop/Dealer Price$1074.16 - $1572.52

Show example Chevrolet Silverado 1500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(3)

Rating Summary

3

0

0

0

0

3

0

0

0

0

SEE REVIEWS NEAR ME

Joe

36 years of experience

958 reviews

Joe

36 years of experience

by Ruth Green

Silverado 1500 2006 - Brake Drum - St. Petersburg, FL

Excellent experience!

Francisco

10 years of experience

45 reviews

Request Francisco

Francisco

10 years of experience

Request Francisco

by Hollis Polvado

Silverado 1500 2010 - Exterior Door Handle - Austin, TX

Was very fast ! Put a driver side door handle on in about 25 minutes ! The labor rate was reasonable and so was door handle ! Will probable hire again soon ! THANKS FRANCISCO !

Joshua

6 years of experience

35 reviews

Joshua

6 years of experience

by Patricia Hawkins

Silverado 1500 2000 - Starter - Argyle, TX

Once again, STELLAR SERVICE from Joshua!! Can't ask for a better tech!

Jesse

15 years of experience

14 reviews

Jesse

15 years of experience

by Jeff Smallwood

Silverado 1500 2013 - Exterior Door Handle - Daytona Beach, FL

Very nice to deal with. Made repair super quick. Highly recommend.

Excellent Rating

(3)

Rating Summary

3

0

0

0

0

3

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

Is It Safe to Drive During Lightning?

You You have almost certainly heard that the best place for you to be in a lightning storm is in your car, but is that really true? Not necessarily. Of course there are worse places to be, like a golf...

P0803 OBD-II Trouble Code: Upshift Solenoid Control Circuit Malfunction

P0803 P0803 code definition The P0803 code is known as the 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction. What the P0803 code means The P0803 fault code is only found in manual vehicles, because it’s part of the system...

How to Become a Certified Mobile Vehicle Inspector (State Car Inspector Certified) in Connecticut

Automotive technician jobs include mobile vehicle inspectors. Learn how to do car checks in Connecticut through state-certified training.

Car powertrain light came on then car cut off and wnt come back on

Hello, thank you for writing in. The first thing we need to do is scan the vehicle for diagnostic codes. When the check engine light illuminates it means to computer has detected a problem, and we can figure out what...

My Nissan Frontier truck is overheating. The smog technician said it needs a new thermostat. Would you like to take a look, give m

Hello, thank you for writing in. If the overheating is only happening when you are at a stop, then you want to focus on the water pump and the cooling fans first. While the thermostat can cause overheating when it...

I have codes p0135, p01131 and 1132. Where should I start?

Hi There, Code P0135 relates to the heating element on in the oxygen sensor (https://www.yourmechanic.com/services/oxygen-sensor-replacement), which hats up the sensor quicker in order for more precise fuel control and reduced emissions. When this element fails, this will trigger this code....

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com