Chevrolet HHR Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet HHR Brake Drum Replacement is $327 with $166 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2010 Chevrolet HHRL4-2.2L	Service typeBrake Drum Replacement	Estimate$607.10	Shop/Dealer Price$713.88 - $980.22
2006 Chevrolet HHRL4-2.2L	Service typeBrake Drum Replacement	Estimate$493.56	Shop/Dealer Price$593.62 - $855.45
2009 Chevrolet HHRL4-2.4L	Service typeBrake Drum Replacement	Estimate$524.76	Shop/Dealer Price$632.61 - $917.85
2008 Chevrolet HHRL4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$708.77 - $1039.70
2011 Chevrolet HHRL4-2.2L	Service typeBrake Drum Replacement	Estimate$521.10	Shop/Dealer Price$623.95 - $887.34
2007 Chevrolet HHRL4-2.4L	Service typeBrake Drum Replacement	Estimate$493.56	Shop/Dealer Price$593.61 - $855.45
2007 Chevrolet HHRL4-2.2L	Service typeBrake Drum Replacement	Estimate$502.06	Shop/Dealer Price$601.88 - $863.54
2009 Chevrolet HHRL4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$594.22	Shop/Dealer Price$717.72 - $1048.97

Show example Chevrolet HHR Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(350)

Rating Summary

325

13

4

2

6

325

13

4

2

6

SEE REVIEWS NEAR ME

Jonathan

5 years of experience

2 reviews

Request Jonathan

Jonathan

5 years of experience

Request Jonathan

by Thomas F Springsdorf

HHR 2010 - Shift Interlock Solenoid - Mobile, AL

Very Knowledgeable about the work that needed done

Shawn

11 years of experience

8 reviews

Shawn

11 years of experience

by Pam ZellnerSeligman

HHR 2006 - Alternator - Newbury Park, CA

What a simple experience! In this day and age of weirdness and covid, Shawn made this so simple. He came to our home with all the parts needed and tools to do the repair. I didn't have to drive somewhere and leave it. Try to figure out how to get home and then try to figure out how to get back to pick up the car. It was all done right here. He came early because someone cancelled on him. So he was able to do the repair earlier than expected. He completed the job cleanly and efficiently. He was very kind and thorough. I will definitely use this site again. I am happy I was able to run across this site. It save a lot of grief.

Kevin

20 years of experience

478 reviews

Kevin

20 years of experience

by Claudia S Janka

HHR 2011 - Brake Rotor/Disc - Stone Mountain, GA

Fast service and efficient

JOHNNY

31 years of experience

120 reviews

JOHNNY

31 years of experience

by Robert Salgado

HHR 2010 - Car pulls in one direction - Citrus Heights, CA

Johnny had the most amazing knowledge and I had the best experience with him. I would recommend him to everyone I know that needs help or has a car issue. Johnny was chill asked questions provided information and more. I couldn't have thanked him enough.

Excellent Rating

(350)

Rating Summary

325

13

4

2

6

325

13

4

2

6

SEE REVIEWS NEAR ME

Recent articles & questions

How to Buy a Good Quality Accelerator Pump

Nestled Nestled down in the carburetor’s fuel bowl is a little pump that provides extra sprays of needed fuel in situations like starting the car or passing on the highway. Fuel-injected vehicles do not need this pump; it is only...

P0705 OBD-II Trouble Code: Transmission Range Sensor Circuit Malfunction (PRNDL Input)

P0705 code definition Transmission Range Sensor Circuit Malfunction (PRNDL Input) What the P0705 code means Diagnostic trouble code P0705 indicates that the...

What are the Car Pool Rules in Nevada?

Nevada Nevada is not a city that’s known for its freeways. The state is known mostly for the glitz and glamor of Las Vegas, but when it comes to driving, people associate Nevada with long, gorgeous, rural dessert roads (https://www.yourmechanic.com/article/top-10-scenic-drives-in-nevada),...

Dome light unit fell down

The sun visor has no serviceable parts and would need to be replaced if it is unable to stay in its stowed position. If the mounting hardware on the dome light is damaged then the dome light assembly will need...

Need to replace Accelerator Pedal Position Sensor

The TPS and a scanner to test it is all that you need. The code P0122 (https://www.yourmechanic.com/article/p0122-obd-ii-trouble-code-throttle-pedal-position-sensor-switch-tps-a-circuit-low-input-by-jay-safford) points to the sensor but a through pinpoint test should be done to make sure the sensor is failing before you replace it....

Recieved the signed title but no bill of sale after purchasing a car

no charge for this answer: If the seller has signed over the vehicle to you, by conveying the ORIGINAL title (that is by signing the title over to you) you should not need additional "proof" of sale. The "conveyed" title...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com