Chevrolet G10 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet G10 Brake Drum Replacement is $395 with $214 for parts and $180 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1976 Chevrolet G10V8-5.7L	Service typeBrake Drum Replacement	Estimate$919.68	Shop/Dealer Price$1104.60 - $1605.38
1976 Chevrolet G10V8-6.6L	Service typeBrake Drum Replacement	Estimate$688.52	Shop/Dealer Price$827.70 - $1191.14
1994 Chevrolet G10V6-4.3L	Service typeBrake Drum Replacement	Estimate$923.27	Shop/Dealer Price$1088.19 - $1474.74
1982 Chevrolet G10V8-5.0L	Service typeBrake Drum Replacement	Estimate$647.20	Shop/Dealer Price$777.37 - $1116.15
1983 Chevrolet G10V8-5.0L	Service typeBrake Drum Replacement	Estimate$609.20	Shop/Dealer Price$735.44 - $1071.28
1985 Chevrolet G10V6-4.3L	Service typeBrake Drum Replacement	Estimate$638.40	Shop/Dealer Price$769.17 - $1114.13
1975 Chevrolet G10V8-5.7L	Service typeBrake Drum Replacement	Estimate$883.68	Shop/Dealer Price$1068.32 - $1568.88
1995 Chevrolet G10V6-4.3L	Service typeBrake Drum Replacement	Estimate$947.27	Shop/Dealer Price$1113.32 - $1500.73

Show example Chevrolet G10 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(10)

Rating Summary

10

0

0

0

0

10

0

0

0

0

SEE REVIEWS NEAR ME

Harish

27 years of experience

588 reviews

Harish

27 years of experience

by Jason

Chevrolet G10 V8-5.0L - Alternator - Charlotte, North Carolina

Install went well.

Luis

18 years of experience

325 reviews

Luis

18 years of experience

by Joseph

Chevrolet G10 L6-4.1L - Starter - Elizabeth, New Jersey

Prompt, honest and friendly. Couldnt ask for more in a mechanic

Ejnar

29 years of experience

107 reviews

Ejnar

29 years of experience

by Sherri

Chevrolet Silverado 1500 V8-4.8L - Brake Drum - Hayward, California

He showed up on time, completed the job on schedule and is a very friendly person.

Terrance

20 years of experience

63 reviews

Request Terrance

Terrance

20 years of experience

Request Terrance

by Thomas

Chevrolet Colorado L5-3.5L - Brake Drum - Nashville, Tennessee

Best mechanic in Nashville. Great guy, great skills, totally local American, will be calling him again. Thanks for the great service! Now get that motorcycle division on line!!!

Excellent Rating

(10)

Rating Summary

10

0

0

0

0

10

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Buy a Good Quality Idle Control Valve

There There are many different times when you will be idling your car; when you’re sitting in front of the gas station waiting for someone to go in and grab a snack or a drink, or while you’re sitting in...

P0067 OBD-II Trouble Code: Air Assisted Injector Control Circuit High

P0067 P0067 trouble code definition Air Assisted Injector Control Circuit High What the P0067 code means The P0067 code means that the powertrain control module (PCM) is detecting a higher voltage from the air assisted injector system circuit than was...

How to Make Your Car More Artful

In In the 1970s, in the middle years of the pop art movement, race car driver Hervé Poulain had an idea. Inspired by the unconventional artistry surrounding the 70s, he commissioned his friend, artist Alexander Calder to create art using...

How do I use the Best Average Fuel Economy setting?

The driver information center (DIC) provides you with a lot of information. At any moment, you can choose what information you want the DIC to display. To have the Best Average Fuel Economy setting displayed, press the Menu button on...

Having an issue with a 2000 ford tauras , the battery is dead I know for sure but every time I charge it , reinstall it , leave it

Hi there. When the battery fails to charge correctly it is due to one of three things typically. First, it's possible the battery is worn out and low on cranking amps and simply needs to be replaced. Second, it's possible...

I am getting [brake](/topics-brake-dodge/), rotors and calipers replaced. Mechanic gave a quote exceeding 800$ so I’m looking to buy the parts and just pay for labor. Im seeing unloaded calipers for 70 bucks but im seeing loaded calipers around 700 bucks so im confused which one I am supposed to buy for the mechanic. I Already have rotors and brakes just need calipers for the rear

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com