Chevrolet Astro Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet Astro Brake Drum Replacement is $332 with $171 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2005 Chevrolet AstroV6-4.3L	Service typeBrake Drum Replacement	Estimate$681.72	Shop/Dealer Price$820.29 - $1197.72
2001 Chevrolet AstroV6-4.3L	Service typeBrake Drum Replacement	Estimate$592.06	Shop/Dealer Price$708.50 - $1005.96
2000 Chevrolet AstroV6-4.3L	Service typeBrake Drum Replacement	Estimate$592.06	Shop/Dealer Price$708.49 - $1005.96
1987 Chevrolet AstroL4-2.5L	Service typeBrake Drum Replacement	Estimate$550.26	Shop/Dealer Price$657.57 - $930.02
2002 Chevrolet AstroV6-4.3L	Service typeBrake Drum Replacement	Estimate$592.06	Shop/Dealer Price$708.53 - $1006.02
1999 Chevrolet AstroV6-4.3L	Service typeBrake Drum Replacement	Estimate$592.06	Shop/Dealer Price$708.49 - $1005.96
1993 Chevrolet AstroV6-4.3L	Service typeBrake Drum Replacement	Estimate$613.56	Shop/Dealer Price$730.67 - $1028.64
1992 Chevrolet AstroV6-4.3L	Service typeBrake Drum Replacement	Estimate$593.56	Shop/Dealer Price$709.51 - $1006.62

Show example Chevrolet Astro Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(141)

Rating Summary

127

9

1

2

2

127

9

1

2

2

SEE REVIEWS NEAR ME

Chris

16 years of experience

419 reviews

Chris

16 years of experience

by Angela

Chevrolet Astro V6-4.3L - Starter - San Francisco, California

Chris was great! Very knowledgeable. It was easy for us to trust his recommendations without having to worry that we were being gouged.

Yoel

9 years of experience

212 reviews

Yoel

9 years of experience

by Dennis

Chevrolet Astro V6-4.3L - Brake pedal is spongy - Philadelphia, Pennsylvania

Yoel is a very knowledgeable mechanic and has a great personality. I would recommend him to anyone.

Corey

17 years of experience

337 reviews

Corey

17 years of experience

by BRIAN

Chevrolet Astro V6-4.3L - Car is not starting - Charlotte, North Carolina

Extremely nice, pleasant, very knowledgeable, a straight and honest shooter. I had no issue at all. He was about an hour behind the appointment time, but he called way ahead of time to let me know that his other appointment was running over. I appreciate that because that let me know he was focused on making sure every one of his customers felt like they were a priority and that he was not going to leave until the job was done right just for the sake of making sure he was on time to the next appointment. I will definitely use him again in the future.

Patrick

33 years of experience

1412 reviews

Request Patrick

Patrick

33 years of experience

Request Patrick

by brid

Chevrolet Astro V6-4.3L - Check Engine Light is on - Austin, Texas

Nice guy - but, good job I spotted he had left a vital part out, from under the 'dog house', after putting it back on.

Excellent Rating

(141)

Rating Summary

127

9

1

2

2

127

9

1

2

2

SEE REVIEWS NEAR ME

Recent articles & questions

How to Buy a Good Quality Throttle Body

Just Just like the throttle, the throttle body plays a very important part in how your fuel-injected engine runs, and makes the car move. The air intake system relies on the throttle body as a pivotal component. The air intake...

How to Install an Ignition Switch

When When your ignition switch (https://www.yourmechanic.com/parts/ignition-switch) fails, it can cause a number of different issues. You may experience anything from a failure to start, to a stalling problem, to a series of electrical issues. There is never a good time...

P0289 OBD-II Trouble Code: Cylinder 10 Injector Circuit High

P0289 P0289 code definition The DTC P0289 code indicates that the number 10 cylinder is experiencing an above average amount of current at the fuel injector. What the P0289 code means Code P0289 means that the fuel injector circuit for...

Car leaking and overheating.

The engine in your vehicle is well known for having coolant leaks from the elbows at the belt tensioner. However, there are many places coolant can leak from. The best way to pinpoint a coolant leak is by performing a...

Why are the fans staying on when the car is off to where I have to pull the fuse?

The fans are controlled by a relay as well as a temperature switch and possibly timer(s). The relay may be stuck in the closed position and that would be the first and easiest component to test. If a relay tests...

My car had electrical damage due to rodents and needs dash harness replaced. How long does a harness replacement typically take?

The wiring harness in the dash would need to be repaired most likely since the new harness would not be available anywhere. The labor will be on a time and materials basis and most mechanics would not want to take...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com