BMW M3 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW M3 Brake Drum Replacement is $348 with $224 for parts and $123 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1998 BMW M3L6-3.2L	Service typeBrake Drum Replacement	Estimate$666.10	Shop/Dealer Price$826.26 - $1211.11
1988 BMW M3L4-2.3L	Service typeBrake Drum Replacement	Estimate$572.33	Shop/Dealer Price$717.10 - $1078.15
2010 BMW M3V8-4.0L	Service typeBrake Drum Replacement	Estimate$1724.17	Shop/Dealer Price$2157.15 - $3371.59
1999 BMW M3L6-3.2L	Service typeBrake Drum Replacement	Estimate$632.10	Shop/Dealer Price$792.24 - $1177.06
2013 BMW M3V8-4.0L	Service typeBrake Drum Replacement	Estimate$1739.78	Shop/Dealer Price$2177.00 - $3392.71
1996 BMW M3L6-3.2L	Service typeBrake Drum Replacement	Estimate$632.10	Shop/Dealer Price$792.33 - $1177.23
2002 BMW M3L6-3.2L	Service typeBrake Drum Replacement	Estimate$633.54	Shop/Dealer Price$791.43 - $1170.60
1991 BMW M3L4-2.3L	Service typeBrake Drum Replacement	Estimate$598.83	Shop/Dealer Price$749.49 - $1114.96

Show example BMW M3 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(76)

Rating Summary

69

5

2

0

0

69

5

2

0

0

SEE REVIEWS NEAR ME

Chris

16 years of experience

419 reviews

Chris

16 years of experience

by Alan

BMW M3 V8-4.0L - Oil Change - San Francisco, California

Chris was great! He was fast and knew what needed to be done. Knew the BMWs well!

Matthew

11 years of experience

53 reviews

Request Matthew

Matthew

11 years of experience

Request Matthew

by ronald

BMW M3 L6-3.0L - Shock Absorber Replacement (Rear) - Alhambra, California

mathew was a great qualified mechanic., he was knowledgeable, and efficient.

Tyrone

11 years of experience

423 reviews

Tyrone

11 years of experience

by Mark

BMW M3 L6-3.0L Turbo - Tire Rotation - Bethesda, Maryland

Very professional service

Edgar

25 years of experience

41 reviews

Edgar

25 years of experience

by Brendan

BMW M3 V8-4.0L - Pre-purchase Car Inspection - Burlingame, California

Edgar was very vague in his description of "exhaust noise" so I still can't pinpoint it at the gasket, headers, catalytic converter, etc. Also the report was too vague in assessments, using words like "OK" everywhere. There weren't many specific notes I could use for selling the car. The pictures I asked him to take of the car were also poor and limited in numbers - I had to go back and do that myself.

Excellent Rating

(76)

Rating Summary

69

5

2

0

0

69

5

2

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

P0030 OBD-II Trouble Code: HO2S Heater Control Circuit (Bank 1 Sensor 1)

P0030 Trouble code definition P0030 is the code for HO2S Heater Control Circuit (Bank 1 Sensor 1) What the P0030 code means...

P0270 OBD-II Trouble Code: Cylinder 4 Injector Circuit Low

P0270 P0270 code definition Cylinder 4 Injector Circuit Low What the P0270 code means This diagnostic trouble code (https://www.yourmechanic.com/article/what-is-the-on-board-diagnostics-obd-system) indicates that the powertrain control module (https://www.yourmechanic.com/article/what-is-a-vehicle-s-electrical-control-unit) has detected a lower reference voltage from the fuel injector on the number 4...

How to Get Porsche Dealership Certified

Porsche car dealerships offer automotive technician jobs to mechanics who are Porsche certified through the Porsche Technology Apprentice Program.

Ac and heater are not blowing air

Hi there: In many cases, the failure of the blower motor to actually blow air into the cabin is caused by a blower motor resistor (https://www.yourmechanic.com/article/how-long-does-a-heater-blower-motor-resistor-last). This component is usually installed behind the dashboard or underneath the blower motor and...

Undercoating the car prior to inclement weather?

Hi there. The undercoating you're father is referring to was a very common factory or aftermarket addition in the Northern United States from the mid-1950's up until the late 1990's. It was essentially a polymer spray that protected exposed steel...

the flywheel bolts broke how hard and what will cost to get fixed ballpark figure

When a bolt breaks off inside the bolt hole, getting it out usually requires drilling. If the transmission is inside the vehicle still and there is not enough room for a drill, the transmission will require removal in order to...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com