BMW i4 Car starts and then dies Inspection at your home or office.

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(17)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(17)

Car starts and then dies Inspection Service

How much does a Car starts and then dies Inspection cost?

On average, the cost for a BMW i4 Car starts and then dies Inspection is $105 with $0 for parts and $105 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2022 BMW i4ElectricService typeCar starts and then dies InspectionEstimate$124.99Shop/Dealer Price$133.39 - $139.69
Show example BMW i4 Car starts and then dies Inspection prices

Starting a vehicle only to have it quit immediately after can be confusing and annoying for many drivers especially if their vehicle has not experienced this type of issue before. Typically, a vehicle will start and then quit because of an issue with the fuel or electrical system. It is important to monitor fuel levels as well as warning lights which can signal to the driver that a vehicle may quit unexpectedly.

How this system works:

To start a vehicle, the electrical system, composed of the battery and starter, turns the engine over. Once running, the engine requires a constant flow of gasoline and good spark to keep that fuel igniting. If gasoline is not readily available, or if there is not enough spark, the engine will quit. More modern vehicles with sophisticated computers may affect the way the vehicle runs. These computers help the car run efficiently but can also shut a car down if the fuel/air mixture is not correct. While an older vehicle may be less sophisticated and easier to diagnose, the computers on modern cars can provide more specific information when connected to a code scanner/reader.

Common reasons for this to happen:

  • Mass Airflow Sensor: The mass airflow sensor measures how much air is entering the engine and relays this information to the vehicle’s computer so that the right amount of fuel can be delivered from the fuel injectors. When a sensor begins to fail, the vehicle’s computer may generate an error code to indicate that something has gone wrong. An issue with the mass airflow sensor may manifest itself when a car starts and then stalls soon after starting.

  • Fuel Pump Relay: The fuel pump relay functions much like a fuse for an electric fuel pump. The fuel pump relay engages as the vehicle is started and starts the fuel pump. While the vehicle is running, the fuel pump relay turns off and the fuel pump is powered by the oil pressure sending unit. If the vehicle’s computer is unable to keep the fuel pump relay running throughout the starting process, the vehicle may start and quit immediately after starting.

  • Ignition Coil: Your vehicle’s ignition coil takes the low voltage of the battery and provides the thousands of volts needed to create a spark in the spark plugs. When an ignition coil begins to fail, it may struggle to provide consistent spark to the plugs, causing the engine to stall after starting.

What to expect:

A top-rated mobile mechanic will come to your home or office to determine the reason why the vehicle starts and then dies. The mechanic will then provide a detailed inspection report outlining why the vehicle quit and the cost of any repairs that need to be made.

How it's done:

A mechanic will begin diagnosing your vehicle’s issue by plugging a code reader/scanner into the vehicle’s computer. The mechanic should be able to get more information from your vehicle’s computer on what component has failed. Using this information, the mechanic can begin necessary repairs.

If your vehicle has a bad or failing mass airflow sensor, the mechanic will begin by finding the sensor in the engine bay and checking for any signs of failure. The mechanic should check the wire harness connected to the sensor to ensure that all of wires are properly connected. After removing the sensor, the mechanic should be able to discover the nature of the failure and replace the sensor.

If the mechanic suspects an issue with the fuel pump relay, he or she should check the vehicle’s computer for a problem. If the vehicle’s computer is having difficulty providing consistent power to the fuel pump relay, the computer may need to be reprogrammed or replaced. If the vehicle’s computer is functioning normally, the mechanic may need to replace the fuel pump relay.

If the mechanic suspects that the ignition coil may be faulty, he or she should first disconnect the battery before beginning work. The mechanic should then begin the process of disconnecting wires from the ignition coil and removing it from the engine bay. The mechanic will then install the new ignition coil and ensure that it is connected properly. The mechanic should then reconnect the battery and test the new coil.

With all repairs, the mechanic will ensure the newly installed parts work properly. The mechanic can then turn off and warning lights that may have come on while the vehicle was not running properly.

How important is this service?

If your vehicle is starting but dying soon after starting, you should have it checked out by a mechanic. Issues involving the fuel management and electrical systems will become worse if not dealt with. Diligence and paying attention to warning lights may help prevent further damage to critical engine component and may save money in repairs. A vehicle that quits after starting can be inconvenient and having a mobile mechanic inspect and repair you vehicle will ensure that you and your vehicle are back on the road soon.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(17)

Rating Summary
14
1
0
0
2
14
1
0
0
2

Mitchel

25 years of experience
239 reviews
Mitchel
25 years of experience
BMW X5 L6-3.0L - Car starts and then dies - Miami, Florida
Above and beyond

RYAN

6 years of experience
103 reviews
RYAN
6 years of experience
BMW X5 L6-3.0L - Car starts and then dies - San Antonio, Texas
Awesome Job.

Keven

8 years of experience
187 reviews
Keven
8 years of experience
BMW 525i L6-2.5L - Car starts and then dies - Puyallup, Washington
Keven was awesome ! Showed up on time with everything he needed. Got the issue diagnosed quick & got it fixed on the spot. I wiill definitely be using your mechanic again for future services ! Thank you keven!!

Keith

19 years of experience
406 reviews
Keith
19 years of experience
BMW 328i xDrive L6-3.0L - Car starts and then dies - Lakeland, Florida
Excellent mechanic

Excellent Rating

(17)

Rating Summary
14
1
0
0
2
14
1
0
0
2
Number of BMW Car starts and then dies Inspection services completed
187+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

Nebraska Speed Limits, Laws, and Fines
Following Following is an overview of the laws, limits, and fines as they relate to speeding traffic violations in the state of Nebraska. Speed limits in Nebraska Nebraska has one of the highest interstate speed limits in the country. As...
Veteran and Military Driver Laws and Benefits in Pennsylvania
For For military members, renewing licenses and registrations can be downright impossible, particularly if you’re stationed outside of Pennsylvania, or even outside the country. Thankfully, the state makes things relatively simple for active duty military members and their families. There...
P2237 OBD-II Trouble Code: O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1
What What the P2237 code means P2237 is an OBD-II generic code for the engine control module (ECM) detecting the O2 sensor for bank 1 sensor 1 and has an open circuit for the heater control circuit of the O2...

No fuel pressure

Lack of fuel pressure can be caused by a failing fuel pump or a clogged fuel filter. Depending on the fuel pressure specification, the fuel pump can be condemned. A proper diagnostic inspection should be performed in order to prove...

My AWD is not working

Hey there. This could be anything from something simple as a differential clutch connector problem to something more serious, such as a mechanic failure with clutches, rear axle, or coupling. You should have a Check Engine Light of some kind...

Automatic transmission warning light.

Hi there. Since the warning light is coming on, I would usually scan the computer for codes (https://www.yourmechanic.com/article/how-to-read-and-understand-check-engine-light-codes-by-jason-unrau) to see what is going on. Most of the time this is caused by a failure in one of the transmission sensors...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com