BMW 325xi Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 325xi Brake Drum Replacement is $373 with $231 for parts and $142 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2006 BMW 325xiL6-3.0L	Service typeBrake Drum Replacement	Estimate$634.09	Shop/Dealer Price$775.74 - $1141.63
2005 BMW 325xiL6-2.5L	Service typeBrake Drum Replacement	Estimate$750.96	Shop/Dealer Price$928.14 - $1392.61
2004 BMW 325xiL6-2.5L	Service typeBrake Drum Replacement	Estimate$750.96	Shop/Dealer Price$928.14 - $1392.60
2002 BMW 325xiL6-2.5L	Service typeBrake Drum Replacement	Estimate$750.96	Shop/Dealer Price$928.07 - $1392.48
2003 BMW 325xiL6-2.5L	Service typeBrake Drum Replacement	Estimate$625.04	Shop/Dealer Price$770.78 - $1140.84
2001 BMW 325xiL6-2.5L	Service typeBrake Drum Replacement	Estimate$750.96	Shop/Dealer Price$928.14 - $1392.60

Show example BMW 325xi Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(70)

Rating Summary

62

3

1

0

4

62

3

1

0

4

SEE REVIEWS NEAR ME

Enrique

21 years of experience

244 reviews

Request Enrique

Enrique

21 years of experience

Request Enrique

by Andrea

BMW 325xi L6-2.5L - Oil Change - Kissimmee, Florida

Very kind and answered all our questions.

Chris

26 years of experience

126 reviews

Chris

26 years of experience

by Mary

BMW 325xi L6-2.5L - Pre-purchase Car Inspection - Sacramento, California

Great having Chris taking the guess work out of buying a used car. Great feedback from him.

Oswaldo

22 years of experience

29 reviews

Request Oswaldo

Oswaldo

22 years of experience

Request Oswaldo

by Kelechi

BMW 325xi L6-3.0L - Car Heater Blower Motor Replacement - Somerset, New Jersey

This was my first experience with this service and It was superb!! my mechanic Oswaldo was just great! He was professional, Honest, and very knowledgable about the issues with my car. He took his time to briefly explain everything step by step. -And, I can't forget how convinent the whole ordeal was, the whole fix up was done outside of my residence. I will definitely use this service again.

William

34 years of experience

523 reviews

Request William

William

34 years of experience

Request William

by Thomas

BMW 325xi L6-3.0L - Oil Change - Glendale, Arizona

William was on time for our appointment and was positive and friendly. Unfortunately, 2 out of the 3 services he was not able to perform as BMW cars require special tools and a skillset as well. Communication between the corporate office and mechanic failed on this particular call. Won't place blame on him as it is not fully his responsibility. So we agreed that "it is what it is". Thanks anyway, William. : )

Excellent Rating

(70)

Rating Summary

62

3

1

0

4

62

3

1

0

4

SEE REVIEWS NEAR ME

Recent articles & questions

How to Replace an Oxygen Sensor

Oxygen Oxygen sensors are one of the most important components on a modern vehicle’s engine management system. They are responsible for monitoring the air fuel mixture of the engine, and their readings affect important engine functions such as timing and...

What Happens When You Drive With the Parking Brake On?

Leaving a parking brake (https://www.yourmechanic.com/article/how-the-parking-brake-works) on in a vehicle while driving is a common occurrence and an easy mistake to...

How to Replace an Exhaust Gas Recirculation (EGR) Vacuum Modulator

The EGR vacuum modulator meters the EGR valve in some car systems. Some signs of a failing EGR vacuum modulator include stalling and a rough idle.

Load on truck's engine causes loud knocking noise

Hello. It sounds like there may be a problem with the piston or the valves in cylinder 5. Loose rod bearings to the piston can cause a knocking noise and/or a misfire condition (https://www.yourmechanic.com/services/engine-is-misfiring-inspection). A worn out piston can also...

New clutch but vehicle just revs when put into gear

Hey there. The clutch is self-adjusting and after service the pedal should be pressed five times to set the pedal free travel. If the clutch still does not engage then you may have a defective clutch pressure plate if the...

My car is hard to start - do I have bad battery cables?

Hi there: If you turn the key on your Jeep and the engine cranks over every time, then the starting problem is most likely not the battery cables. However, if you turn the key and it takes a few times...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com