Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.
How A Diagnostic Works
Instantly book a certified mobile mechanic to come to you
Mechanic diagnoses the problem and quotes necessary repairs
Your vehicle is ready to go
Fair, upfront & transparent pricing for all services
Our certified mobile mechanics can come to you now.
On average, the cost for a Audi Cabriolet Clutch is not fully disengaging Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.
| Car | Service | Estimate | Shop/Dealer Price |
|---|---|---|---|
| 1998 Audi CabrioletV6-2.8L | Service typeClutch is not fully disengaging Inspection | Estimate$114.99 | Shop/Dealer Price$132.49 - $145.62 |
| 1995 Audi CabrioletV6-2.8L | Service typeClutch is not fully disengaging Inspection | Estimate$94.99 | Shop/Dealer Price$112.52 - $125.67 |
| 1994 Audi CabrioletV6-2.8L | Service typeClutch is not fully disengaging Inspection | Estimate$94.99 | Shop/Dealer Price$112.52 - $125.67 |
| 1996 Audi CabrioletV6-2.8L | Service typeClutch is not fully disengaging Inspection | Estimate$94.99 | Shop/Dealer Price$112.48 - $125.60 |
| 1997 Audi CabrioletV6-2.8L | Service typeClutch is not fully disengaging Inspection | Estimate$94.99 | Shop/Dealer Price$112.55 - $125.72 |
Your car’s clutch is what allows you to change gears. When you press the clutch pedal, the clutch moves away from flywheel, stopping the rotation and allowing you to shift to a higher or lower gear without causing damage (grinding gears does your transmission no good at all). When you release the clutch pedal, the clutch should press up against the flywheel and you should be able to proceed in the newly selected gear. However, there are some situations in which the clutch may not fully disengage.
To put it in a nutshell, clutches work based on friction. When the clutch pedal is pressed, either a cable or a piston (depending on the type of clutch is installed in your vehicle) will push the release fork. This causes the throw out bearing to press against the diaphragm spring.
The center of the spring is pushed in, which engages a series of pins. These pull the pressure plate away from the clutch disc and separate the clutch from the engine flywheel. When you take your foot off the pedal, the reverse happens, and the clutch is engaged.
Clutch components are subject to a significant amount of wear and tear (because they work on friction – this is normal). The most common problem here is the disc wearing. The material is a lot like what you’ll find on your brake pads, and the operating concept is also very similar. Of course, that creates slippage, which isn’t the problem here. Failure to disengage is called “sticking”, and there are several potential causes.
Stretched/Broken Clutch Cable: If the clutch cable is broken or stretched, then the clutch will stick (not disengage). You’ll notice the sticking becoming more and more common as the cable continues to stretch.
Leaking Hydraulic System: If you have a hydraulic clutch, it’s possible that either the slave or master cylinder (or both) is leaking. This means that insufficient hydraulic pressure is built up for the clutch system to operate correctly.
Misadjusted Linkage: The linkage connects the clutch pedal to the transmission. If it’s incorrectly adjusted, the clutch may not disengage properly.
Incompatible Aftermarket Parts: If you’ve recently had clutch work done, it’s possible that aftermarket components were installed in your car. Not all aftermarket parts will work correctly with your clutch, and this can cause it to not fully disengage.
A top-rated mobile mechanic will come to your home or office to inspect the entire clutch system and determine the source and cause of the problem. The mechanic will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.
The mechanic will need to inspect the clutch, as well as the cable or hydraulic system. Both a visual inspection and a test drive may be required. Once the underlying cause has been determined, the mechanic will recommend the next step.
If your clutch is not fully disengaging, it means that the flywheel and clutch disc are not fully separating. This causes additional wear not only on the clutch material, but on other components in the system (including the input shaft).
The best defense against transmission problems is to ensure that you work with a reputable mechanic for general maintenance who can inspect and troubleshoot problems as they arise. It’s also important to ensure that any aftermarket clutch components installed are fully compatible with your vehicle. If you’re experiencing problems with the clutch not fully disengaging, one of our professional mechanics can inspect and repair the problem.
Fast and easy service at your home or office
Backed by 12-month, 12.000-mile guarantee
Real customer reviews from Audi owners like you.
Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.
