Epc, power steering, abs and brake lights all popped up a...
Responses
eauto
278 days ago
Hello and thank you for using JustAnswer. My name is \*\*\*\*\* \*\*\*\*\* I will do my best to assist you. During this conversation you will be given an automated offer for a phone call. You may accept or decline that offer. They are sent thru by Justanswer and not me.
So Please IGNORE them unless you PREFER a PHONE CHAT!
I’m sorry that you’re having trouble with your vehicle. I will do my best to help you resolve them. Please understand that I do not know your knowledge or capabilities so I may need to ask questions to find out basic information to help solve your specific problem.
My aim is to give you the best service possible and to help you. If you have any questions or concerns, please don’t hesitate to let me know. Sometimes it may take a moment for me to respond because I may have to look up information about your concern. I appreciate your patience and will provide responses as soon as possible.
Customer
278 days ago
Hi johnDo you have any additional questions to ask at the moment?
eauto
278 days ago
Have you scanned for fault codes yet?
Customer
278 days ago
I dont have a code reader.
eauto
278 days ago
The ABS and epc and brake warning lights comes on when the on-board computer detects a fault in abs or stabil trac system and a fault code is set and stored in the computer. Faults that can set the check engine light can range from a speed sensor a leak, a sensor low engine compression, faulty tone ring or other sensors or hydraulic pressure , open/short in wiring harness, system leak, or one of over a hundred different reasons.
The only way to know what set a fault code and turned the light on is to have a diagnostic scanner hooked up to the on-board computer and read it for stored diagnostic fault codes. if you do not have a scan tool then you will have to take it to a shop and pay to have the computer read for stored fault codes.
Without knowing the fault codes numbers, it would be irresponsible to guess as to the cause as there are hundreds of possible causes
if you provide me a diagnostic code we can narrow down the cause of failure
Customer
278 days ago
Ok, thank you for your help.
eauto
278 days ago
You're welcome
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
How do I connect an auxiliary device?
You can play an external device through your sound system, via the auxiliary jack. To do so, follow these steps: 1. Locate the auxiliary port, which is in the center console. 2. Make sure your device is turned off. 3....
How changing differential and transfer case affects fuel economy
Well, they could, but only to a small amount. If you go and put the whole synthetic, it would have a little bit less friction, but not all that much.
Regarding All Wheel Drive
Hi Chrysler 300 owner: With only 20,000 miles on a 2014 Chrysler 300 AWD, you definitely should not be experiencing any jerking type motion while you drive under normal operation. A few of the potential mechanical problems that cause similar...
Engine stalling issue
Volkswagen has come under fire recently with several of their TDI diesel engines. Although these problems are related to engine emissions, it was also shown to cause intermittent stalling; as the computer would reduce fuel flow to create a very...
Foot pedal vibration at certain RPM's?
The vibration still sounds like it could be coming from a worn engine or transmission mount. You may be able to do a simple check by engaging the parking brake and putting the vehicle in drive and blipping the throttle...
cold start issues
Hi Jim. The poor cold start may be related to a faulty/dirty IAC (idle air control) valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) not allowing engine RPM (revolutions per minute) to increase with ambient temperatures below 30 degrees. Assuming the check engine light is on...
Air not flowing out of front vents.
If the blower motor is not turning, the cause is identified during a failed heater diagnostic (https://www.yourmechanic.com/services/heater-is-not-working-inspection). Blower motors failures are due to faults in the wiring, fuse, relay (https://www.yourmechanic.com/services/blower-motor-relay-replacement), control switch (https://www.yourmechanic.com/services/blower-motor-switch-replacement), resistor block (https://www.yourmechanic.com/services/heater-blower-motor-resistor-replacement), if so equipped, and...
Engine stalls sometimes but not all the time
Hello, Unfortunately, without additional information as to the make, model and year of your motorcycle it may not be possible to suggest what may be causing it to stall. Depending on whether or not it is fuel injected, or not...
i want to replace engine mounts of 2008 c300 4matic, so let me know how many and where engine mounts are on the car
Using Mercedes Benz' nomenclature, there is a front left, front right and rear (transmission) mount. If you are trying to diagnose and/resolve a vibration problem in the vehicle do not buy aftermarket motor mounts. The original mounts installed in the...
Browse other content
Estimates
Maintenance
Cities
Epc, power steering, abs and brake lights all popped up ay the same time after loosing power when driving. Replaced a dead battery but those lights are still on Mechanic's Assistant: Is it just the ABS light? Or is the bra...
Epc, power steering, abs and brake lights all popped up ay the same time after loosing power when driving. Replaced a dead battery but those lights are still on Mechanic's Assistant: Is it just the ABS light? Or is the brake system warning light on, too? Brake light is on too. Red flashing Mechanic's Assistant: What is the make/model/year of your car? Vw rabbit 2007 Mechanic's Assistant: Are you fixing your Rabbit yourself? What have you tried so far? I took the battery in to be tested at autozone and found out it was dead so I replaced it myself. Thats it so far Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? Oh it has a bit of a rough idle