I have a Ford tourneo connec, the engine management light...


I have a Ford tourneo connec, the engine management light came on while reversing up a hill Mechanic's Assistant: Just to clarify, what are the exact lights you're talking about? The yellow management light Mechanic's...

I have a Ford tourneo connec, the engine management light came on while reversing up a hill Mechanic's Assistant: Just to clarify, what are the exact lights you're talking about? The yellow management light Mechanic's Assistant: What is the model/year of your Ford? 2017 Ford connect Mechanic's Assistant: Are you fixing your vehicle yourself? What have you tried so far? I have a reset tool & turned it off but it came back on while reversing at the same place, just looking to see if something simple or whether it needs a trip to the garage Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? No that’s it

Automotive Expert
Morning my name is \*\*\*\*\* \*\*\*\*\* you have the code that was stored.

Sorry I don't
Automotive Expert
I could of done with that other than the warning light how does it drive.

drives normally no loss of power
Automotive Expert
With no codes it would be a guess do you have any Bosch approved independents near you rather than the cost of a main dealer put your post code in workshop finder [http://www.boschcarservice.com](http://www.boschcarservice.com)

What others are asking

Need error codes fixed
Hi. P0133 is a code for the oxygen sensor bank one sensor. P0410 is a code for the secondary air injection system malfunction and P0301 is a code for a misfire on cylinder 1. I would suggest having a certified...
Security system won't let car start
I strongly suggest allowing a technician to inspect the vehicle's electrical system (https://www.yourmechanic.com/services/electric-problems-inspection) as it may simply be wire out of place or a blown fuse causing the vehicle not to start. When immobilizer systems become problematic usually immobilizer components...
Need to start car after sitting for a few years
Hi there, the battery will be completely dead since the vehicle hasn't been driven for so long. You could try charging the battery overnight or try jumpstarting the car. With any luck the battery will still be able to hold...
My fans stay on when I turn my car on and my temperature gauge stays on cool and will not move up even when the car is running
Hey there. This can be caused by a number of things such as low coolant levels (https://www.yourmechanic.com/services/top-off-coolant), a faulty thermostat (https://www.yourmechanic.com/services/thermostat-replacement), or a failing coolant fan switch (https://www.yourmechanic.com/services/thermo-coolant-fan-switch-replacement). As you may know, the coolant fan switch helps to maintain the...
New car oil consumption before 1st oil change
Hi there. Either the positive crankcase ventilation valve (PCV (https://www.yourmechanic.com/services/positive-crankcase-ventilation-pcv-valve-replacement)) or the turbo has excessive oil blow by. Check the PCV valve and see if its working. Check the air filter to the engine and make sure that its dry...
How to clean the air intake system..
If the intake system (throttle body and intake manifold) are that clogged up, the safest route may be to remove them completely for a thorough cleaning. Cleaning it while still attached to the engine creates the risk of even the...
V6 motors
Hi there. Many factors will impact fuel economy and efficiency on any gasoline or diesel powered vehicle. Driving "slow" isn't always as vital to fuel economy. However, what is important is being smooth with the acceleration. The allure of "quick...
idler pulley
I think you mean the a/c compressor is seized and not the condenser. You will need to get an a/c compressor bypass kit and the compressor can then be removed and a pulley in its place. The problem is these...
Car starts n idles fine. When I put it in gear it stalls. I'm thinking transmission fluid problems? Also it "CLANKS" when shifting
The torque converter and torque converter lock up solenoid should be evaluated. Another possibility is an internal hydraulic leak in transmission seals causing pressure to apply both reverse and forward gears at the same time, lock up the transmission and...