Recently swapped my 90 eclipse gst with a 92 engine after...


Recently swapped my 90 eclipse gst with a 92 engine after the. The swap i got a barometric pressure sensor cel . i then replaced the maf with a new on , stilll get the same cel? Mechanic's Assistant: Does the light stay on...

Recently swapped my 90 eclipse gst with a 92 engine after the. The swap i got a barometric pressure sensor cel . i then replaced the maf with a new on , stilll get the same cel? Mechanic's Assistant: Does the light stay on, or does it blink? At start up its off after car is at operating temp it will stay on Mechanic's Assistant: Are you fixing your Eclipse yourself? What have you tried so far? Upgraded the throttle body to 92 Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? Since Swapping the engine to To 92 could swapimg a 92 ecu fix the problem since the car is currently on the 90 ecuu

Automotive Expert
Hello and thank you for using Just Answer. I am an ASE Certified Technician who will be further assisting you. Sorry to hear you're having issues with your Eclipse. I know it can be frustrating, but let's see what we can do to get you going.

Hello
Automotive Expert
Does your old engine have a Barometric pressure sensor? Sorry, I see its built in the MAF

The barometric pressure sensor is build in with the mafI replced the maf. With a new one but still got the same cel codeBoth engines have the same mafI was wondering the car. Is still on the ecu will swapping to a 92 ecu fix my problemOops car is on 90 ecu currentlyAre u still there?

What others are asking

hesitation when accelerating and shaking when in idle
Hey there. A proper diagnosis at a repair shop is the only way to be certain. If the spark plugs (https://www.yourmechanic.com/services/spark-plugs-replacement) have not been changed in 40,000 miles or more, the car would benefit from replacing them. But any number...
My car does not go past 40 kmph while driving
This is a common problem that can be caused by a clogged catalytic converter. If the converter is clogged or partially clogged, the exhaust gasses cannot escape the engine as fast as they should and this chokes the engine. Typically,...
Uneven brake rotor wear
Hello. I tried to view the pictures but the link seems to be broken. It sounds like you have two different problems reading the description of the problem. The first is the brake pads (https://www.yourmechanic.com/services/brake-pads-replacement) being too tight and binding...
Turn key to start, lose all power, it resets and starts. Battery is not dead.
If you are losing all battery power intermittently but your car's battery is testing good, check the battery clamp connections to the cables for corrosion. The cables will show green tinted corrosion at or near the connections where the cables...
Misfiring. Changed the fuel pump and the plugs
Hi there. It depends on what type of digital scanner you're using, but most professional scanners will be able to see the misfiring cylinder on the scope while the engine is running. This will typically also indicate which electrical sensor...
A single clicking noise when i try to start my car
Hi There, I believe the shop is correct in that this is related to a faulty starter solenoid. Depending on the particular model of your Suzuki, this may have a starter solenoid that is external from the starter (meaning it...
My car won't stay starred & is shaking badly 2009 Toyota Camry
Hello - I believe you have had either a failure of one of the timing chain (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-timing-chain) guides, or possible the timing chain tensioner has allowed your engine to "jump time" - the chain actually jumps a few teeth on...
Overheating issue with my 2007 Chrysler Sebring
The first thing is a proper diagnosis will not only verify the complaint but will locate the cause of the problem for you so you can decide to fix it or not. When an engine overheats for no apparent reason...
Where is the crankshaft sensor on a 2011 vw cc sport 2.0
The crankshaft sensor is in center of motor near flywheel even with starter on engine block.