2000 youkon dinalli won’t start,cranks but won’t turn ove...
Responses
Daniel Chaidez
250 days ago
Good Afternoon, my name is \*\*\*\*\* \*\*\*\*\* ill be helping you, so sorry to hear about the issues here on the Yukon. I know how frustrating it can be to deal with crank no starts. If the battery was disconnected i agree that we are likely dealing with a security system issue. On this model you can reset it by turning the key to the on position and letting it sit there for 10 minutes and then turn it off for 30 seconds. repeat that process two more times. If the vehicle still will not start up you will need a locksmith to re-program the key to the vehicle and reset the security system that way.
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Do I need to program the Sentry Key immobilizer system?
The Sentry Key immobilizer system is a security feature in your car. The system disables the engine if an unauthorized key is used to try and start the vehicle. This helps keep your vehicle from being stolen. The Sentry Key...
Engine code P0325.
Hello, p0325 is a code for a Knock Sensor Circuit Malfunction. There is either a sensor fault or the wiring for the sensor to the engine control unit is shorted or has an open circuit. The first thing to check...
P0171
Hi there. This code you are getting is due to your system running lean (https://www.yourmechanic.com/article/p0171-obd-ii-trouble-code-system-too-lean-bank-1-by-andrew-quinn). Most of the time, it is caused by low fuel pressure from a weak fuel pump (https://www.yourmechanic.com/services/fuel-pump-replacement) or a clogged fuel filter (https://www.yourmechanic.com/services/fuel-filter-replacement). Another possible...
How safe is it to drive with a torn caliper boot?
Hello, thanks for writing in to YourMechanic. If the caliper boot is torn open then you will get dirt, debris, water, and road salts in the caliper piston surface. The caliper may seize or tear the caliper piston seal causing...
hi, im having a problem with my steering wheel it keeps on shaking when im like 55 to 60 mph I'vegot my wheels balance and a wheel
If a tire is defective (belt separation, uneven wear, even design defects such as unusual or uneven stiffness) no amount of balancing will eliminate a vibration. So, among the first things to confirm is the condition of the tires (and...
A leak from power steering pressure line hose
Hello. If that other hose is leaking then it will need to be replaced also. If the section of hose that is leaking is the metal line then that can usually only be purchased at the dealer. This line is...
2011 Pathfinder Fluctuating idle, stalling, no power when accelerating
Hi There, It sounds like you may have a dirty or failing idle air control valve causing your engine idle to fluctuate. The idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) is a small valve on the engine's intake system that reads the...
Radiator / heater core issues 2002 Dodge Ram 1500
Hello - these two unfortunate events are probably only related in the sense that they are both caused by advanced mileage and age. New radiators utilize plastic end tanks that are crimp-sealed onto an aluminum fin section. The plastic in...
Smaller serpentine belt shredded and pieces went into the crank shaft Tried to start timing jumped. How do I fix? 05' kia op 2.4L
The KIA 2.4 liter motor is what is called an interference motor and this means it will bend valves if the timing belt breaks or jumps timing. You will need to have cylinder head removed and bent valves replaced if...
Browse other content
Cities
Services
Maintenance
2000 youkon dinalli won’t start,cranks but won’t turn over, it’s my friends, someone had told him it’s in safe mode because work has been done on it,battery disconnected,etc. so I’m inquiring on how to get out of safe mode Mec...
2000 youkon dinalli won’t start,cranks but won’t turn over, it’s my friends, someone had told him it’s in safe mode because work has been done on it,battery disconnected,etc. so I’m inquiring on how to get out of safe mode Mechanic's Assistant: Have you checked the engine's fuel supply? And the spark plugs -- are they all working? Yes and yes,he’s worked on cars for a long time so the basics are covered. It’s just every model has a different sequence to reboot computer part of system, like w my Mitsubishi diamonte ya turn key for 3 seconds off for 10 on for 5...so on... I need to find the sequence for his 2000 youkon dinalli,sorry it’s spelled incorrectly idkhow to spellbit Mechanic's Assistant: Are you fixing your Yukon yourself? What have you tried so far? See above messagw Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? No thankyou