My horn and brake lights are not working
Responses
Brent Redfern
226 days ago
Hello my name is\*\*\*\*\* that you are having trouble with your Mazda. First let's discuss the horn fuse blowing. If it blows as soon as you install the fuse you have a direct short to ground. The first place I would look would be under the dash at the bash of the steering column. Look for a chaffed wire or broken wire. If one is found make the repair.
For the brake light issue I would start at the brake light switch. Do you have power coming into the switch and power going out when it is activated? If yes, check the brake light bulbs. Also, if you have power going out have someone double check to see if the brake lights activate when the switch is pressed. The switch may have simply backed out of it's slot.
Another question has any electrical work been done under the dash of this car lately? If so, what?
The reason the car is stuck in park is because the transmission gear selector is not seeing the brakes being pressed (switch activated).
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
How should my car be towed?
There are many instances in which you might want to tow your car. You might want to tow it behind an RV for instance. While some vehicles can be towed in almost any way, yours is not among them. You...
Radiator cap needs replacing.
If you have a white residue building up just below the cap and you have to add coolant frequently, this could be the issue. The cooling system and cap need to be pressure tested to ensure the system is not...
Car won't charge
Hello! Since you have replaced the battery, we will put that to the side, but we cannot ignore it. A failed charging system puts a large load on a battery and can damage a new one, so I suggest having...
Broke my alternator wire
You will need a heavy duty set of crimping pliers, a butt connector or terminal, and possibly a short section of wire. I would assume the wire is about 4 gauge in thickness. Take the broken piece to an automotive...
Alternator not charging
The alternator charging rate is controlled by the engine control module under the air cleaner housing. You should disconnect the battery and check the connections at the engine control module and look at pin 54 on connector one (C1). It...
replaced oil pan gasket, engine and trans mount Jaguar Stype
Hello, thank you for writing in. It is always disheartening to hear these reports. From here you are going to want to either take it back to the original mechanic with the complaint, and discuss any further charges to take...
I have a 2006 Jeep Grand Cherokee Laredo. 4 wheel drive. I have an oxygen sensor bad. Code p0152 and P0132. Are these upstream or
Hello - both of these sensors are "pre-catalytic converter" or in front of the cats in the exhaust stream (P0152 (https://www.yourmechanic.com/article/p0152-obd-ii-trouble-code-o2-sensor-circuit-high-voltage-bank-2-sensor-1-by-jay-safford)/P0132 (https://www.yourmechanic.com/article/p0132-obd-ii-trouble-code-o2-sensor-circuit-high-voltage-bank-1-sensor-1)). This is what the "Sensor 1" portion of the problem code means. I recommend an oxygen sensor replacement...
My 2002 Saturn Vue's rpms started revving into 4-5k when up shifting. Later that day the clutch went out. Now the starter is out.
Hello, thank you for writing in. The decision to invest in an older car is difficult, even more so when you do not have the car in front of you. A failed clutch can interfere with the flywheel causing the...
How to remove headliner in '03 Cadillac CTS
Hi Andy. I believe we attempted to answer your question yesterday. Most people that have this problem will take their vehicles to a Cadillac dealership to have this completed. The main reason why we don't complete this service or provide...
Browse other content
Maintenance
Cities
Services
My horn and brake lights are not working Mechanic's Assistant: Have you checked the brake fluid? How's the level and when was it last changed? The brake fuses are fine but the fuse for the horn keeps blowing soon as I put...
My horn and brake lights are not working Mechanic's Assistant: Have you checked the brake fluid? How's the level and when was it last changed? The brake fuses are fine but the fuse for the horn keeps blowing soon as I put a new one in Mechanic's Assistant: What is the make/model/year of your car? 2005 mazda 3 2.3L The brakes are working fine but the lights arenot And the car is stuck in park I have to bypass it Im pretty sure the shift solenoid is bad but I just don't know whats going on with the brake lights Mechanic's Assistant: Are you fixing your Mazda 3 yourself? What have you tried so far? Ive checked the fuses Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? Ive disconnected the brake light switch and reconnected it but im not sure if it is bad or not