I have a 2010 jeep commandor that wont crank


I have a 2010 jeep commandor that wont crank Mechanic's Assistant: Have you checked the fuel supply? And are all the spark plugs working? Its making a clicking sound Mechanic's Assistant: What is the model of your...

I have a 2010 jeep commandor that wont crank Mechanic's Assistant: Have you checked the fuel supply? And are all the spark plugs working? Its making a clicking sound Mechanic's Assistant: What is the model of your '10 Jeep? Commandor Mechanic's Assistant: Are you fixing your vehicle yourself? What have you tried so far? I replaced the starter so far.. doing what I can myself still clicking Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? The power windows and radio are not coming on but all other things come on with power

Automotive Expert
Hello and thank you for using Just Answer. I am an ASE Certified Technician who will be further assisting you. Sorry to hear you're having issues with your Jeep. I know it can be frustrating, but let's see what we can do to get you going. Please tell me if you have tested the battery and how many cranking amps present.

I have not tested the batteryHave not texted the battery yetTested
Automotive Expert
I believe you may have a faulty battery or possible too much resistance on your battery cables (bad terminals or wires). You will need to get battery tested and if clicking continues, you will need to bench test and possible replace starter. Keep in mind aftermarket starters tend to fail often from the box.

I replaced starter with new already. But didn't check battery.
Automotive Expert
Let's start there and if all good, test cables for resistance. If both are good, I would suspect a faulty starter.

OkHow can I follow up with you again on same topic if this doesn't work
Automotive Expert
Just respond on here, the questions will stay open for a couple days. Otherwise ask for MBR Auto if you open a new question if this one expires.

Ok thanks
Automotive Expert
You're welcome and thank you for using JA.

What others are asking

Convertible top doesn't close properly
Hi. The convertible top has to be reset so it is synchronized to all of its upper and lower limits. If this procedure does not work, then the top position switch may need to be replaced or adjusted. I recommend...
Drive shaft replaced, now van won't go forward
I am not aware of any problems about removing and replacing a driveshaft when the vehicle is warm. I however have seen transaxle damaged from not installing the axle all the way into the transmission and engaging the axle fully...
Interior lights sunroof windows
Hello there, it is not uncommon for a vehicle to have a few electrical issues as they start to get older. Although the amount of issues seen here is a bit abnormal for your 2006 Jaguar Vanden Plas. The most...
Won't start w/ no engine turn over. (Intermittent)
The system uses a starter relay (https://www.yourmechanic.com/services/starter-relay-replacement) that is in the engine compartment fuse box. This relay is activated by the ignition switch through the clutch switch and engine control module. You may have a bad relay or problems with...
Burning engine oil and have gray smoke coming from below the engine and the tailpipe.
Hi there. If you are getting gray smoke from under the vehicle and in the engine compartment, then there is an external oil leak. The oil is leaking onto the exhaust pipe and then burning off. This is why you...
My car stopped while driving and wont go into gear
Hi there. What seemed to happen is transmission may have broke a something inside it like a thrust bearing or a drive sun shell. This is common for the transmission to do on normal driving as the vehicle ages. I...
Hi Patrick my car has the code p1090 coming out I got the part and wanted to know what else I should look out for in my car and to
You should go ahead and replace the actuator first and then clear the codes and road test to see if the system operates correctly and if the code returns then you may have to have further diagnosis of the electrical...
convert 1978 k5 blazer 4WD to 2WD
If you are trying to measure and position a frame, use a "tram", which is a specialized frame measuring tool. If, though, you are looking for specific frame dimensions, off of each vehicle, so that you can design a "composite"...
My reverse went out and the car won’t go over 20mph. It’s making noises as well.
The first thing to do is verify the fluid condition and if it is full. If the fluid is full then smell the fluid and put some fluid on a white towel to see if it is very dark and...