Hey there... I have a 2012 Ford Explorer.. the [engine](/...
Responses
MichelleWiganN122
218 days ago
Hello
Thanks a lot for the question,
You need to connect the OBDII connector to the scanner and read the fault codes.
If you don't have a scanner, you can try and do the following:
Press and hold the reset button for the odometer.
Turn the key on to accessory.
Keep holding the button until the words TEST appear.
Once the words TEST appear let go of the odometer button and press it again to cycle through the onboard test.
Push the button to dtc which will give an error codes.
Thanks!
Customer
218 days ago
I have an OBD2 connector and there are no codes or DTC's being thrown at all
MichelleWiganN122
218 days ago
OK, in that case if the vibration is too high, I wouldn't touch anything. I would recommend to revise the motor belts, but nothing else.
You may also consider replacing the rubbeer motor support that prevents the vibration of the motor traspasing to the body of the vehicle.
Customer
218 days ago
what does "revise the motor belts" mean?also, if it were the motor mount, it should shake more than just at idle, right?
Customer
218 days ago
hello?
MichelleWiganN122
218 days ago
It will vibrate at any given RPM, however some specific RPM may cause resonance in the motor compartment. It may happend at IDLE or at any specific RPM value.
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Car clicks and doesn't start.
Even though it just clicks the battery can still be the problem. Low battery voltage wont have enough juice to turn the starter all the way. The partial engagement will sound like a click. A few other things like bad,...
Coolant leaking into cylinders
Hi. As coolant is burned through the combustion chamber, it travels through the exhaust which can damage your catalytic converter. This will lead to the clogging of your exhaust and can cause different problems with your vehicle. If you need...
I hear a squeaky sound from the front when i step on tge brake and turn the straing and another sound when i enter a rough road
Hello there, many faults will cause your 2007 Toyota Corolla to have a squeak when the brakes are pressed or turning. The most common causes would be worn brake pads, suspension bushing, wheel bearings, front struts, CV axle, or a...
Car doesn't hold idle, I tried changing the PCV valve, what else could be wrong?
If you have to remove the PCV valve (https://www.yourmechanic.com/services/positive-crankcase-ventilation-pcv-valve-replacement) to make the vehicle operate correctly, then there is an issue with the combustion in the engine. The rings to the cylinders are not sealing properly and causing lots of blow...
Pcv valve problem
Hello. In most case a PCV valve should not noticeably rattle, though that varies from engine to engine. If it appears to be rattling excessively that could signify that the PCV valve is not secured properly, that there is a...
How to take air out of cooling system Lexus ls400 1997?
Hi there. First check the cooling system for the right amount of coolant and top it off if its low. Then run the cooling system until the engine is hot at operating temperature. Shut off the engine and let it...
How do I remove a broken bolt out of thermostat housing
Hi there. If the bolt is sticking out, then you can use a pair of vice grips to help remove the bolt or weld on a nut. If the bolt is broke off inside the threaded gallery, then you will...
Recently replaced engine due to water damage. Now car shakes at idle and check engine light flashes.
If your catalyst is bad then I would suggest replacing it first and then clear codes and see how engine runs afterwards and if it needs further diagnosis.
Hello, I have 2009 Hyundai Sonata with about 114,000 miles on it. The car jerks...sometimes violently when I'm driviing and go to
Hi Taheem. Thanks for contacting us today. It depends on what you mean by "jerking". If the car is pulling to one side while braking, this could indicate a bad caliper, worn brake pads, faulty wheel bearing or even tire...
Browse other content
Cities
Estimates
Maintenance
Hey there... I have a 2012 Ford Explorer.. the [engine](/topics-engine-ford/) shakes violently when I put it into either reverse or drive (no shake in park or neutral) Mechanic's Assistant: How many miles are on the Ford? ...
Hey there... I have a 2012 Ford Explorer.. the [engine](/topics-engine-ford/) shakes violently when I put it into either reverse or drive (no shake in park or neutral) Mechanic's Assistant: How many miles are on the Ford? Is it an automatic or a manual [transmission](/topics-transmission-ford/)? 100K miles, automatic Mechanic's Assistant: Are you fixing your Explorer yourself? What have you tried so far? Replaced the transmission mount and the [spark plugs](/topics-spark-plug-ford/) Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? It's only at idle.. once you start driving the shake goes away