Had p030300 diagnostics code come up .. had the coil pack...


Had p030300 diagnostics code come up .. had the coil pack [spark plugs](/topics-spark-plug-chevy/) and ht leads changed and still saying same Mechanic's Assistant: How many miles are on the Chevrolet? When did you last cha...

Had p030300 diagnostics code come up .. had the coil pack [spark plugs](/topics-spark-plug-chevy/) and ht leads changed and still saying same Mechanic's Assistant: How many miles are on the Chevrolet? When did you last change the plugs? It’s a Skoda and today they got changed Mechanic's Assistant: What year is your Spark? 2015 Mechanic's Assistant: Are you fixing your Spark yourself? What have you tried so far? No garage changed it and new coil pack new spark plugs and new ht leads Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? No Thankyou

Automotive Expert
Good morning, my name is \*\*\*\*\* \*\*\*\*\* ill be helping you, so sorry to hear about the issues here on the Chevy. I know how frustrating it can be to deal with misfires. Now just so im clear are we only dealing with a P0303 code or also a P0300?

It’s a Skoda rapid and yea p0303
Automotive Expert
P0303 indicates a misfire on cylinder 3, if the [ignition coil](/topics-ignition-coil-chevy/) and spark plug were ruled out we would next need to suspect a fuel or compression related issue. i would start with swapping the injector for cylinder with a different cylinder to see if the code changes, as well as checking for power and ground to both the injector and the ignition coil to rule out an electrical issue. finally i would also recommend you test compression on all of the cylinders to see if theres a mechanical issue which is possible here.

What others are asking

Replaced chewed wires fixed the problem, but only for a little while.
Hello, having damaged wiring can cause all kinds of issues, the only proper way to repair wiring is to cut off the damaged portion, strip the wiring, then solder the wiring together and use wiring shrink tubing to cover up...
Driver side door not opening
It sounds like you have a bad door latch or something is broken in the door. A common problem with that car is the spring for the door latch breaks not allowing the door to open. The fix is going...
Car not starting after replacing battery
Hi there. The most common cause of that vehicle not starting is the fuel pump and fuel filter. Over time, the pump motor will stop working and needs to be replaced. I would recommend having a technician come out and...
AC blower going out?
The clogged line caused the evaporator case to flood out. The problem is the blower motor and the blower motor control resistor may of got flooded out with the water and caused them to short out. If you can get...
My ford 500 2007 leaked out the oil and shut down on the road. The leak is fixed but it wont start. What could be the problem
When you leaked out all the oil, the oil pressure was lost in the engine. This loss of pressure caused all the moving parts to be starved of oil and no longer lubricated. You most likely seized the engine bearings....
3 warning lights on, power steering, VMS, and electronic lights. Any clue?
The fact that these lights are on is a warning to the driver that there are fault codes stored because one of more control systems have detected a problem. The vehicle will have to be read with a code scanner...
Idling low at 1 to 1.5k rpm. can not get rpms above 3k.
It sounds like you may have a couple of different issues going on here. At idle your car should be hovering around 750-800 RPM's consistently. This is generally controlled by the idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) which a valve that...
Car over heating
Hello there. Every car has a system that circulates coolant, a mixture of anti­-freeze and water, through the engine to absorb heat created by the combustion process and the friction created by moving parts within the engine. The hot liquid...
Emergency brake light not working properly
You will need to have the skid control ECU scanned for proper input from parking brake to see if the fault is in the parking brake, ECU or instrument cluster. A mechanic like one from YourMechanic can come and test...