Hi,My driver window dosent work well. When I press it to ...
Customer
Hi,My driver window dosent work well. When I press it to go down it goes down fine but when I press it to come up, it goes up so far to then come back down again..... it repeats this a few times. I have to keep pressing it in smal...
Hi,My driver window dosent work well. When I press it to go down it goes down fine but when I press it to come up, it goes up so far to then come back down again..... it repeats this a few times. I have to keep pressing it in small sections to get it to the top
Read More
Responses
Jaybird61
285 days ago
Automotive Expert
Hi my name is\*\*\*\*\* you tried to lube both sides of window guides with silicone spray to see if it helps? If motor binds it will reverse.
Customer
285 days ago
No not yet, where is the best place to get it?
Jaybird61
285 days ago
Automotive Expert
Any parts store or even Wallmart will have it in automotive section. It may be called drylube or silicone spray. Just roll down window and spray in both side window guides and move window up and down.
Jaybird61
285 days ago
Automotive Expert
Let me know if any other questions?
Customer
285 days ago
How do I install a parking camera to the screen and also fit a dash cam. Also LED floor lights from eBay that change colour so the wires don’t show.
Jaybird61
285 days ago
Automotive Expert
You will need to open additional questions for these other items since this would be in another area of vehicle repair.
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
If it got that after you did the tires it could be that they didn't balance them right. I had a big peeve happen to me about six months ago. I got new tires for my wife at a NTW...
Hello. When your car has been in an accident, the impact will cause it to go into a fail safe mode. While in fail safe mode, the car may come on but you will be unable to drive. This is...
Hi there. Thanks for writing in about your 2003 Lexus SC430. Another brake component that may cause the brakes to stick are the front and rear calipers (https://www.yourmechanic.com/services/brake-caliper-replacement). The calipers are what presses the brake pads against the rotors. If...
Hello. A few things I would check are the timing, the idle air control valve, and the condition of the vacuum hoses. Retarded ignition timing can sometimes cause low throttle issues, and can definitely cause stalling. The idle air control...
Hello. The EPS light comes on when the computer detects an issue with the electronic power steering system. If the power steering is hard, and the computer has been replaced then it may be possible that the issue lies elsewhere....
Hello there, a few common faults can cause your 1972 Oldsmobile Cutlass to only work on the #2 speed air flow. You are correct, the blower motor resistor (https://www.yourmechanic.com/services/cooling-fan-resistor-replacement) could cause this fault. Other likely causes would be the fan...
Hi there. The valve cover gaskets are probably worn and need replaced. If all of the gaskets are replaced and there is still oil coming out of the engine, then replace the positive crank case vent valve (PCV). If the...
ABS is capable of monitoring differentials in wheel speeds, and rates of deceleration, and there is no way the ABS system could "know" whether the brakes are in good repair or not. However, if the caliper was seized such that...
Hi There, This code is a generic code relating to the mass air flow sensor indicating that there is a lean air/fuel mixture. This can happen when the mass air flow sensor (https://www.yourmechanic.com/services/mass-airflow-sensor-replacement) is dirty or faulty. I would suggest...
Hi,My driver window dosent work well. When I press it to go down it goes down fine but when I press it to come up, it goes up so far to then come back down again..... it repeats this a few times. I have to keep pressing it in smal...
Hi,My driver window dosent work well. When I press it to go down it goes down fine but when I press it to come up, it goes up so far to then come back down again..... it repeats this a few times. I have to keep pressing it in small sections to get it to the top