I have a 2004 350z oil pressure gauge was reading 120 stu...
Customer
I have a 2004 350z oil pressure gauge was reading 120 stuck so I changed sensor now gauge reads 0 so I manually checked oil pressure it's fine 40 at warm up idle could I have got bad sender ordered on line or do you think gauge is...
I have a 2004 350z oil pressure gauge was reading 120 stuck so I changed sensor now gauge reads 0 so I manually checked oil pressure it's fine 40 at warm up idle could I have got bad sender ordered on line or do you think gauge is bad and oil light is on
Mechanic's Assistant: Have you checked the oil? How old is your oil pump?
Checked oil pressure manually it's good needle nice and steady 40 psi
Mechanic's Assistant: Are you fixing your 350Z yourself? What have you tried so far?
Yes
Read More
Responses
Kurt Mulling
348 days ago
Automotive Expert
Hi my name is \*\*\*\*\* \*\*\*\*\* I'll try to help you with this issue, the website may assk if you want a call, but that is up to you, So either you have a bad senser or the wrong one.
Customer
348 days ago
you think I got bad sender it's brand new got onlineBefore I changed sensor gauge was stuck at 120 now light on and gauge at zero so checked mechanical y pressure at 40 psi when warm needle steady pressure goodthey sent me a bad sensor
Kurt Mulling
348 days ago
Automotive Expert
most likely
as you have proven the pump is good.
Customer
348 days ago
basically the oil light. Is telling me faulty sensor if it was gauge light would be off
Kurt Mulling
348 days ago
Automotive Expert
yes that's about it.
Customer
348 days ago
I have seven days of trial working on my 2004 350zmy ac clutch not pulling in went straight to wire plug at compressor to see if I have voltage and I have 11.8 volts what's the problem
Kurt Mulling
348 days ago
Automotive Expert
So if there is ground at the other wire then you have a bad clutch coil, which is difficult to change and is best done, by changing the compressor. And even though you have this trial period you need to start a new question. But thanks for asking on JA
Customer
348 days ago
Thanks kurt just wanted to let you know on that first qeustion about oil sender you were right they gave me a bad one went and purchased one locally works fine thanka
Kurt Mulling
348 days ago
Automotive Expert
great
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Ok here is what I found about the fuel cutoff switch. Sometimes the connectors to the inertia switch located in the trunk become corroded and need to be cleaned and re-terminated. I would recommend having a technician come out and...
The bearing or brushes in your alternator are likely going out. You could also have another issue in your belt drive system causing the noise and lack of charging. A visual inspection of the drive system, a stethoscope to listen...
Hello. The main question is why does you think your computer needs to be reset. If you have engine idling issues, then there is a relearn procedure procedure which can be performed with an advanced aftermarket scan tool such as...
Located inside of the fuel tank is a fuel pump that requires amperage to operate. This pump can have an electrical failure that causes it to use more amps than the system is set up for. The fuel pump (https://www.yourmechanic.com/services/fuel-pump-replacement)...
Depending on the location and the specific sound you are hearing, this could be either power steering or CV joints going bad. Generally, CV joints, when going bad, will make more of a popping or clicking sound and will cause...
This sounds like a worn or failing CV joint. All front-wheel drive cars have constant velocity joints or CV joints on both ends of the drive shafts (half shafts). Inner CV joints connect the drive shafts to the transmission while...
Hi there. When the EPS (Electronic Power Steering) light came on after hitting a pot hole in the road, then the jolt could have dislodged a wire from the EPS controller. Look around the steering column for any loose wiring....
Hi there. To remove the horn button and replace it in the steering column / steering wheel, perform the following steps: (1). Disconnect the battery before removing any electrical wiring on your vehicle. (2). Release the airbag by inserting a...
Hello, thank you for writing in. The truck may be having issues with air sensors, fuel pressure, or other electronic issues. I have have to replace the fuel module and the mass airflow on my 1998 S10 with 168,000 miles....
I have a 2004 350z oil pressure gauge was reading 120 stuck so I changed sensor now gauge reads 0 so I manually checked oil pressure it's fine 40 at warm up idle could I have got bad sender ordered on line or do you think gauge is...
I have a 2004 350z oil pressure gauge was reading 120 stuck so I changed sensor now gauge reads 0 so I manually checked oil pressure it's fine 40 at warm up idle could I have got bad sender ordered on line or do you think gauge is bad and oil light is on Mechanic's Assistant: Have you checked the oil? How old is your oil pump? Checked oil pressure manually it's good needle nice and steady 40 psi Mechanic's Assistant: Are you fixing your 350Z yourself? What have you tried so far? Yes