Volvo C30 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Volvo C30 Brake Drum Replacement is $374 with $212 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2011 Volvo C30L5-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$619.72	Shop/Dealer Price$742.79 - $1073.72
2008 Volvo C30L5-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$708.82 - $1039.77
2010 Volvo C30L5-2.4L	Service typeBrake Drum Replacement	Estimate$745.36	Shop/Dealer Price$908.36 - $1359.05
2007 Volvo C30L5-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$743.36	Shop/Dealer Price$905.82 - $1354.98
2012 Volvo C30L5-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$708.84 - $1039.81
2013 Volvo C30L5-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$708.81 - $1039.77
2010 Volvo C30L5-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$594.22	Shop/Dealer Price$717.08 - $1047.86
2009 Volvo C30L5-2.5L Turbo	Service typeBrake Drum Replacement	Estimate$594.22	Shop/Dealer Price$717.72 - $1048.97

Show example Volvo C30 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Volvo mechanics

Real customer reviews from Volvo owners like you.

Excellent Rating

(22)

Rating Summary

19

1

0

1

1

19

1

0

1

1

SEE REVIEWS NEAR ME

Cody

8 years of experience

99 reviews

Cody

8 years of experience

by Tony

Volvo C30 L5-2.5L Turbo - Battery - Fort Worth, Texas

Good experience with Cody who came on time and knows the job. Friendly and professional.

Thomas

12 years of experience

101 reviews

Thomas

12 years of experience

by Steven

Volvo C30 L5-2.5L Turbo - Car is not starting - Cedar Hill, Texas

Very professional and experienced

Logan

49 years of experience

82 reviews

Logan

49 years of experience

by Thomas

Volvo C30 L5-2.5L Turbo - Battery - Livermore, California

Brought the correct battery and completed the job professionally in 10 min.

Andrew

11 years of experience

845 reviews

Andrew

11 years of experience

by Bryant

Volvo C30 L5-2.5L Turbo - Pre-purchase Car Inspection - Kansas City, Missouri

I can put positive imput about Andrew but was not on location, but the communication from Andrew was timely and informative and judging by what the dealer had to say he seems to be very thorough.

Excellent Rating

(22)

Rating Summary

19

1

0

1

1

19

1

0

1

1

SEE REVIEWS NEAR ME

Recent articles & questions

How to Tell If an Air Filter Is Good Quality

Considering Considering that your car’s engine needs 10,000 to 12,000 gallons of air to burn one gallon of gasoline, you need an air filter that will allow only clean air reaches its internal combustion chamber. As you drive, road debris,...

Symptoms of a Bad or Failing Brake Caliper

Common signs include brake fluid leaks, abnormal sounds, and vehicle pulling to the left or right.

P0738 OBD-II Trouble Code: TCM Engine Speed Output Circuit Low

P0738 means that the PCM is unable to receive a signal from the engine output speed sensor due to a faulty engine or transmission sensor, or low fluid

Do you have to remove the transmission on a vacuum pump replacement for 2010 VW Jetta?

The by-the-book way of replacing the brake booster vacuum pump (https://www.yourmechanic.com/services/vacuum-pump-replacement) involves removing the transmission in order to have enough room to do the repair properly, but some experienced technicians can complete the job without removing the transmission. This repair...

I would like to know why my rear end shakes really bad at 55 mph

Hello, thank you for writing in. The vehicle is likely having an issue with the tires or suspension. Typically you start by testing the simpler possibilities and work your way to the more complicated fixes. With that said, one of...

2013 Honda Accord wouldn't start in the morning. Displayed the Electric Power Steering (EPS) warning icon on the dashboard. Vehicl

Hi Steven. Thanks for contacting us today. It's quite possible that the reason the car wouldn't start is related to the battery not being charged enough and not the EPS light. However, it is also possible that an error code...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com