Volkswagen Passat Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Volkswagen Passat Brake Drum Replacement is $268 with $154 for parts and $114 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2006 Volkswagen PassatL4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$585.23	Shop/Dealer Price$705.29 - $1033.97
2012 Volkswagen PassatL4-2.0L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$459.03	Shop/Dealer Price$557.31 - $825.11
2000 Volkswagen PassatL4-1.8L Turbo	Service typeBrake Drum Replacement	Estimate$550.63	Shop/Dealer Price$669.06 - $992.81
2000 Volkswagen PassatV6-2.8L	Service typeBrake Drum Replacement	Estimate$550.63	Shop/Dealer Price$669.03 - $992.75
2018 Volkswagen PassatL4-2.0L Turbo	Service typeBrake Drum Replacement	Estimate$618.34	Shop/Dealer Price$749.62 - $1105.05
2009 Volkswagen PassatV6-3.6L	Service typeBrake Drum Replacement	Estimate$560.10	Shop/Dealer Price$678.16 - $996.27
2014 Volkswagen PassatL5-2.5L	Service typeBrake Drum Replacement	Estimate$584.22	Shop/Dealer Price$706.09 - $1036.13
1994 Volkswagen PassatV6-2.8L	Service typeBrake Drum Replacement	Estimate$458.81	Shop/Dealer Price$552.87 - $802.75

Show example Volkswagen Passat Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Volkswagen mechanics

Real customer reviews from Volkswagen owners like you.

Excellent Rating

(872)

Rating Summary

825

22

5

4

16

825

22

5

4

16

SEE REVIEWS NEAR ME

Alex

16 years of experience

435 reviews

Alex

16 years of experience

by Alfredo

Volkswagen Passat L5-2.5L - Car will not turn over - Frisco, Texas

Great insight on my VW Passat, found other concerning issue. Saved me money in the end. I would give a 5 star rating but appointment time was delayed by more than a few hours than originally scheduled. Arrival updates were provided.

Robert

11 years of experience

20 reviews

Robert

11 years of experience

by Steve

Volkswagen Passat L4-1.8L Turbo - Coolant is leaking - La Verne, California

Robert is very friendly professional funny looked at my vehicle and throughly checked for problem that I had requested to be looked at found the issue and explained what would probably needed to be done to fix issues I would definitely recommend Robert to friends and family and would like for him to repair my car thanks Robert 

Michael

6 years of experience

132 reviews

Request Michael

Michael

6 years of experience

Request Michael

by Leonard

Volkswagen Passat V6-2.8L - Car is not starting - Tacoma, Washington

Friendly, professional and willing to go out of his way to help, i appreciate the service he provided.. thank you for allowing me to meet him.. i will be using the service again...

Chris

6 years of experience

84 reviews

Chris

6 years of experience

by Emaceo

Volkswagen Passat L4-1.8L Turbo - Brake Pads Replacement (Front) - Jonesboro, Georgia

Trust me he knows what he is doing

Excellent Rating

(872)

Rating Summary

825

22

5

4

16

825

22

5

4

16

SEE REVIEWS NEAR ME

Recent articles & questions

A Buyer’s Guide to the 2012 Audi A4

The The 2012 Audi A4 has powerful engines and a spacious interior for both passengers and cargo. In addition, the A4 offers style and performance that others in its class just don’t have. It has steadily improved to overcome the...

P0556 OBD-II Trouble Code: Brake Booster Pressure Sensor Circuit Range/Performance

P0556 code means there is a problem with the brake booster pressure sensor circuit often due too shorted electrical circuitry or defective valves.

B1933 OBD-II Trouble Code: Air Bag Passenger Circuit Open

B1933 means there is a circuit failure in the airbag deployment system on the passenger's side, mostly likely due to an incomplete circuit.

How to change the lifters

In order to replace the valve lifters, removal of the valve covers and rocker arm assemblies is required. The job can be a little extensive and many of the fasteners removed cannot be reused or they may cause damage to...

Hazard lights don't work

Hello there, thank you for asking about your 1990 Oldsmobile Cutlass Calais. There can be an issue with the switch itself or the hazard flasher assembly. The flasher is the device that makes the lights blink and a failure here...

When I turn my key the dash bored goes on and the lights but radio doesn't and car won't start

Hi There, It sounds like you may have a bad ignition relay or potentially a faulty starter relay. You may want to check the ignition relay (https://www.yourmechanic.com/services/ignition-relay-replacement). When you turn the key to the On position, the ignition relay switches...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com